lkml.org 
[lkml]   [2019]   [Aug]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH RFC tip/core/rcu 14/14] rcu/nohz: Make multi_cpu_stop() enable tick on all online CPUs
On Thu, Aug 08, 2019 at 02:30:12PM -0700, Paul E. McKenney wrote:
> On Thu, Aug 08, 2019 at 01:35:41PM -0700, Paul E. McKenney wrote:
> > On Wed, Aug 07, 2019 at 02:41:31PM -0700, Paul E. McKenney wrote:
> > > On Tue, Aug 06, 2019 at 11:08:24AM -0700, Paul E. McKenney wrote:
> > > > On Mon, Aug 05, 2019 at 10:48:00AM -0700, Paul E. McKenney wrote:
> > > > > On Mon, Aug 05, 2019 at 05:50:24PM +0200, Peter Zijlstra wrote:
> > > > > > On Mon, Aug 05, 2019 at 07:54:48AM -0700, Paul E. McKenney wrote:
> > > > > >
> > > > > > > > Right; so clearly we're not understanding what's happening. That seems
> > > > > > > > like a requirement for actually doing a patch.
> > > > > > >
> > > > > > > Almost but not quite. It is a requirement for a patch *that* *is*
> > > > > > > *supposed* *to* *be* *a* *fix*. If you are trying to prohibit me from
> > > > > > > writing experimental patches, please feel free to take a long walk on
> > > > > > > a short pier.
> > > > > > >
> > > > > > > Understood???
> > > > > >
> > > > > > Ah, my bad, I thought you were actually proposing this as an actual
> > > > > > patch. I now see that is my bad, I'd overlooked the RFC part.
> > > > >
> > > > > No problem!
> > > > >
> > > > > And of course adding tracing decreases the frequency and duration of
> > > > > the multi_cpu_stop(). Re-running with shorter-duration triggering. ;-)
> > > >
> > > > And I did eventually get a good trace. If I am interpreting this trace
> > > > correctly, the torture_-135 task didn't get around to attempting to wake
> > > > up all of the CPUs. I will try again, but this time with the sched_switch
> > > > trace event enabled.
> > > >
> > > > As a side note, enabling ftrace from the command line seems to interact
> > > > badly with turning tracing off and on in the kernel, so I eventually
> > > > resorted to trace_printk() in the functions of interest. The trace
> > > > output is below, followed by the current diagnostic patch. Please note
> > > > that I am -not- using the desperation hammer-the-scheduler patches.
> > > >
> > > > More as I learn more!
> > >
> > > And of course I forgot to dump out the online CPUs, so I really had no
> > > idea whether or not all the CPUs were accounted for. I added tracing
> > > to dump out the online CPUs at the beginning of __stop_cpus() and then
> > > reworked it a few times to get the problem to happen in reasonable time.
> > > Please see below for the resulting annotated trace.
> > >
> > > I was primed to expect a lost IPI, perhaps due to yet another qemu bug,
> > > but all the migration threads are running within about 2 milliseconds.
> > > It is then almost two minutes(!) until the next trace message.
> > >
> > > Looks like time to (very carefully!) instrument multi_cpu_stop().
> > >
> > > Of course, if you have any ideas, please do not keep them a secret!
> >
> > Functionally, multi_cpu_stop() is working fine, according to the trace
> > below (search for a line beginning with TAB). But somehow CPU 2 took
> > almost three -minutes- to do one iteration of the loop. The prime suspect
> > in that loop is cpu_relax() due to the hypervisor having an opportunity
> > to do something at that point. The commentary below (again, search for
> > a line beginning with TAB) gives my analysis.
> >
> > Of course, if I am correct, it should be possible to catch cpu_relax()
> > in the act. That is the next step, give or take the Heisenbuggy nature
> > of this beast.
> >
> > Another thing for me to try is to run longer with !NO_HZ_FULL, just in
> > case the earlier runs just got lucky.
> >
> > Thoughts?
>
> And it really can happen:
>
> [ 1881.467922] migratio-33 4...1 1879530317us : stop_machine_yield: cpu_relax() took 756140 ms
>
> The previous timestamp was 1123391100us, so the cpu_relax() is almost
> exactly the full delay.
>
> But another instance stalled for many minutes without a ten-second
> cpu_relax(). So it is not just cpu_relax() causing trouble. I could
> rationalize that vCPU preemption being at fault...
>
> And my diagnostic patch is below, just in case I am doing something
> stupid with that.

I did a 12-hour run with the same configuration except for leaving out the
"nohz_full=1-7" kernel parameter without problems (aside from the RCU CPU
stall warnings due to the ftrace_dump() at the end of the run -- isn't
there some way to clear the ftrace buffer without actually printing it?).

My next step is to do an over-the-weekend run with the same configuration,
then a similar run with more recent kernel and qemu but with the
"nohz_full=1-7". If both of those pass, I will consider this to be a
KVM/qemu bug that has since been fixed.

Thanx, Paul

\
 
 \ /
  Last update: 2019-08-09 18:52    [W:0.110 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site