lkml.org 
[lkml]   [2019]   [Aug]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] Documentation/arm/sa1100: Remove some obsolete documentation
Date
The support for the following boards, among others, was removed in 2004
with commit "[ARM] Remove broken SA1100 machine support.":

- ADS Bitsy
- Brutus
- Freebird
- ADS GraphicsClient Plus
- ADS GraphicsMaster
- Höft & Wessel Webpanel
- Compaq Itsy
- nanoEngine
- Pangolin
- PLEB
- Yopy

Tifon support has been removed in 2.4.3.3.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
---
Documentation/arm/sa1100/adsbitsy.rst | 51 ----------
Documentation/arm/sa1100/brutus.rst | 69 -------------
Documentation/arm/sa1100/freebird.rst | 25 -----
Documentation/arm/sa1100/graphicsclient.rst | 102 --------------------
Documentation/arm/sa1100/graphicsmaster.rst | 60 ------------
Documentation/arm/sa1100/huw_webpanel.rst | 21 ----
Documentation/arm/sa1100/index.rst | 12 ---
Documentation/arm/sa1100/itsy.rst | 47 ---------
Documentation/arm/sa1100/nanoengine.rst | 11 ---
Documentation/arm/sa1100/pangolin.rst | 29 ------
Documentation/arm/sa1100/pleb.rst | 13 ---
Documentation/arm/sa1100/tifon.rst | 7 --
Documentation/arm/sa1100/yopy.rst | 5 -
13 files changed, 452 deletions(-)
delete mode 100644 Documentation/arm/sa1100/adsbitsy.rst
delete mode 100644 Documentation/arm/sa1100/brutus.rst
delete mode 100644 Documentation/arm/sa1100/freebird.rst
delete mode 100644 Documentation/arm/sa1100/graphicsclient.rst
delete mode 100644 Documentation/arm/sa1100/graphicsmaster.rst
delete mode 100644 Documentation/arm/sa1100/huw_webpanel.rst
delete mode 100644 Documentation/arm/sa1100/itsy.rst
delete mode 100644 Documentation/arm/sa1100/nanoengine.rst
delete mode 100644 Documentation/arm/sa1100/pangolin.rst
delete mode 100644 Documentation/arm/sa1100/pleb.rst
delete mode 100644 Documentation/arm/sa1100/tifon.rst
delete mode 100644 Documentation/arm/sa1100/yopy.rst

diff --git a/Documentation/arm/sa1100/adsbitsy.rst b/Documentation/arm/sa1100/adsbitsy.rst
deleted file mode 100644
index c179cb26b682..000000000000
--- a/Documentation/arm/sa1100/adsbitsy.rst
+++ /dev/null
@@ -1,51 +0,0 @@
-===============================
-ADS Bitsy Single Board Computer
-===============================
-
-(It is different from Bitsy(iPAQ) of Compaq)
-
-For more details, contact Applied Data Systems or see
-http://www.applieddata.net/products.html
-
-The Linux support for this product has been provided by
-Woojung Huh <whuh@applieddata.net>
-
-Use 'make adsbitsy_config' before any 'make config'.
-This will set up defaults for ADS Bitsy support.
-
-The kernel zImage is linked to be loaded and executed at 0xc0400000.
-
-Linux can be used with the ADS BootLoader that ships with the
-newer rev boards. See their documentation on how to load Linux.
-
-Supported peripherals
-=====================
-
-- SA1100 LCD frame buffer (8/16bpp...sort of)
-- SA1111 USB Master
-- SA1100 serial port
-- pcmcia, compact flash
-- touchscreen(ucb1200)
-- console on LCD screen
-- serial ports (ttyS[0-2])
- - ttyS0 is default for serial console
-
-To do
-=====
-
-- everything else! :-)
-
-Notes
-=====
-
-- The flash on board is divided into 3 partitions.
- You should be careful to use flash on board.
- Its partition is different from GraphicsClient Plus and GraphicsMaster
-
-- 16bpp mode requires a different cable than what ships with the board.
- Contact ADS or look through the manual to wire your own. Currently,
- if you compile with 16bit mode support and switch into a lower bpp
- mode, the timing is off so the image is corrupted. This will be
- fixed soon.
-
-Any contribution can be sent to nico@fluxnic.net and will be greatly welcome!
diff --git a/Documentation/arm/sa1100/brutus.rst b/Documentation/arm/sa1100/brutus.rst
deleted file mode 100644
index e1a23bee6d44..000000000000
--- a/Documentation/arm/sa1100/brutus.rst
+++ /dev/null
@@ -1,69 +0,0 @@
-======
-Brutus
-======
-
-Brutus is an evaluation platform for the SA1100 manufactured by Intel.
-For more details, see:
-
-http://developer.intel.com
-
-To compile for Brutus, you must issue the following commands::
-
- make brutus_config
- make config
- [accept all the defaults]
- make zImage
-
-The resulting kernel will end up in linux/arch/arm/boot/zImage. This file
-must be loaded at 0xc0008000 in Brutus's memory and execution started at
-0xc0008000 as well with the value of registers r0 = 0 and r1 = 16 upon
-entry.
-
-But prior to execute the kernel, a ramdisk image must also be loaded in
-memory. Use memory address 0xd8000000 for this. Note that the file
-containing the (compressed) ramdisk image must not exceed 4 MB.
-
-Typically, you'll need angelboot to load the kernel.
-The following angelboot.opt file should be used::
-
- base 0xc0008000
- entry 0xc0008000
- r0 0x00000000
- r1 0x00000010
- device /dev/ttyS0
- options "9600 8N1"
- baud 115200
- otherfile ramdisk_img.gz
- otherbase 0xd8000000
-
-Then load the kernel and ramdisk with::
-
- angelboot -f angelboot.opt zImage
-
-The first Brutus serial port (assumed to be linked to /dev/ttyS0 on your
-host PC) is used by angel to load the kernel and ramdisk image. The serial
-console is provided through the second Brutus serial port. To access it,
-you may use minicom configured with /dev/ttyS1, 9600 baud, 8N1, no flow
-control.
-
-Currently supported
-===================
-
- - RS232 serial ports
- - audio output
- - LCD screen
- - keyboard
-
-The actual Brutus support may not be complete without extra patches.
-If such patches exist, they should be found from
-ftp.netwinder.org/users/n/nico.
-
-A full PCMCIA support is still missing, although it's possible to hack
-some drivers in order to drive already inserted cards at boot time with
-little modifications.
-
-Any contribution is welcome.
-
-Please send patches to nico@fluxnic.net
-
-Have Fun !
diff --git a/Documentation/arm/sa1100/freebird.rst b/Documentation/arm/sa1100/freebird.rst
deleted file mode 100644
index 81043d0c6d64..000000000000
--- a/Documentation/arm/sa1100/freebird.rst
+++ /dev/null
@@ -1,25 +0,0 @@
-========
-Freebird
-========
-
-Freebird-1.1 is produced by Legend(C), Inc.
-`http://web.archive.org/web/*/http://www.legend.com.cn`
-and software/linux maintained by Coventive(C), Inc.
-(http://www.coventive.com)
-
-Based on the Nicolas's strongarm kernel tree.
-
-Maintainer:
-
-Chester Kuo
- - <chester@coventive.com>
- - <chester@linux.org.tw>
-
-Author:
-
-- Tim wu <timwu@coventive.com>
-- CIH <cih@coventive.com>
-- Eric Peng <ericpeng@coventive.com>
-- Jeff Lee <jeff_lee@coventive.com>
-- Allen Cheng
-- Tony Liu <tonyliu@coventive.com>
diff --git a/Documentation/arm/sa1100/graphicsclient.rst b/Documentation/arm/sa1100/graphicsclient.rst
deleted file mode 100644
index a73d61c3ce91..000000000000
--- a/Documentation/arm/sa1100/graphicsclient.rst
+++ /dev/null
@@ -1,102 +0,0 @@
-=============================================
-ADS GraphicsClient Plus Single Board Computer
-=============================================
-
-For more details, contact Applied Data Systems or see
-http://www.applieddata.net/products.html
-
-The original Linux support for this product has been provided by
-Nicolas Pitre <nico@fluxnic.net>. Continued development work by
-Woojung Huh <whuh@applieddata.net>
-
-It's currently possible to mount a root filesystem via NFS providing a
-complete Linux environment. Otherwise a ramdisk image may be used. The
-board supports MTD/JFFS, so you could also mount something on there.
-
-Use 'make graphicsclient_config' before any 'make config'. This will set up
-defaults for GraphicsClient Plus support.
-
-The kernel zImage is linked to be loaded and executed at 0xc0200000.
-Also the following registers should have the specified values upon entry::
-
- r0 = 0
- r1 = 29 (this is the GraphicsClient architecture number)
-
-Linux can be used with the ADS BootLoader that ships with the
-newer rev boards. See their documentation on how to load Linux.
-Angel is not available for the GraphicsClient Plus AFAIK.
-
-There is a board known as just the GraphicsClient that ADS used to
-produce but has end of lifed. This code will not work on the older
-board with the ADS bootloader, but should still work with Angel,
-as outlined below. In any case, if you're planning on deploying
-something en masse, you should probably get the newer board.
-
-If using Angel on the older boards, here is a typical angel.opt option file
-if the kernel is loaded through the Angel Debug Monitor::
-
- base 0xc0200000
- entry 0xc0200000
- r0 0x00000000
- r1 0x0000001d
- device /dev/ttyS1
- options "38400 8N1"
- baud 115200
- #otherfile ramdisk.gz
- #otherbase 0xc0800000
- exec minicom
-
-Then the kernel (and ramdisk if otherfile/otherbase lines above are
-uncommented) would be loaded with::
-
- angelboot -f angelboot.opt zImage
-
-Here it is assumed that the board is connected to ttyS1 on your PC
-and that minicom is preconfigured with /dev/ttyS1, 38400 baud, 8N1, no flow
-control by default.
-
-If any other bootloader is used, ensure it accomplish the same, especially
-for r0/r1 register values before jumping into the kernel.
-
-
-Supported peripherals
-=====================
-
-- SA1100 LCD frame buffer (8/16bpp...sort of)
-- on-board SMC 92C96 ethernet NIC
-- SA1100 serial port
-- flash memory access (MTD/JFFS)
-- pcmcia
-- touchscreen(ucb1200)
-- ps/2 keyboard
-- console on LCD screen
-- serial ports (ttyS[0-2])
- - ttyS0 is default for serial console
-- Smart I/O (ADC, keypad, digital inputs, etc)
- See http://www.eurotech-inc.com/linux-sbc.asp for IOCTL documentation
- and example user space code. ps/2 keybd is multiplexed through this driver
-
-To do
-=====
-
-- UCB1200 audio with new ucb_generic layer
-- everything else! :-)
-
-Notes
-=====
-
-- The flash on board is divided into 3 partitions. mtd0 is where
- the ADS boot ROM and zImage is stored. It's been marked as
- read-only to keep you from blasting over the bootloader. :) mtd1 is
- for the ramdisk.gz image. mtd2 is user flash space and can be
- utilized for either JFFS or if you're feeling crazy, running ext2
- on top of it. If you're not using the ADS bootloader, you're
- welcome to blast over the mtd1 partition also.
-
-- 16bpp mode requires a different cable than what ships with the board.
- Contact ADS or look through the manual to wire your own. Currently,
- if you compile with 16bit mode support and switch into a lower bpp
- mode, the timing is off so the image is corrupted. This will be
- fixed soon.
-
-Any contribution can be sent to nico@fluxnic.net and will be greatly welcome!
diff --git a/Documentation/arm/sa1100/graphicsmaster.rst b/Documentation/arm/sa1100/graphicsmaster.rst
deleted file mode 100644
index e39892514f0c..000000000000
--- a/Documentation/arm/sa1100/graphicsmaster.rst
+++ /dev/null
@@ -1,60 +0,0 @@
-========================================
-ADS GraphicsMaster Single Board Computer
-========================================
-
-For more details, contact Applied Data Systems or see
-http://www.applieddata.net/products.html
-
-The original Linux support for this product has been provided by
-Nicolas Pitre <nico@fluxnic.net>. Continued development work by
-Woojung Huh <whuh@applieddata.net>
-
-Use 'make graphicsmaster_config' before any 'make config'.
-This will set up defaults for GraphicsMaster support.
-
-The kernel zImage is linked to be loaded and executed at 0xc0400000.
-
-Linux can be used with the ADS BootLoader that ships with the
-newer rev boards. See their documentation on how to load Linux.
-
-Supported peripherals
-=====================
-
-- SA1100 LCD frame buffer (8/16bpp...sort of)
-- SA1111 USB Master
-- on-board SMC 92C96 ethernet NIC
-- SA1100 serial port
-- flash memory access (MTD/JFFS)
-- pcmcia, compact flash
-- touchscreen(ucb1200)
-- ps/2 keyboard
-- console on LCD screen
-- serial ports (ttyS[0-2])
- - ttyS0 is default for serial console
-- Smart I/O (ADC, keypad, digital inputs, etc)
- See http://www.eurotech-inc.com/linux-sbc.asp for IOCTL documentation
- and example user space code. ps/2 keybd is multiplexed through this driver
-
-To do
-=====
-
-- everything else! :-)
-
-Notes
-=====
-
-- The flash on board is divided into 3 partitions. mtd0 is where
- the zImage is stored. It's been marked as read-only to keep you
- from blasting over the bootloader. :) mtd1 is
- for the ramdisk.gz image. mtd2 is user flash space and can be
- utilized for either JFFS or if you're feeling crazy, running ext2
- on top of it. If you're not using the ADS bootloader, you're
- welcome to blast over the mtd1 partition also.
-
-- 16bpp mode requires a different cable than what ships with the board.
- Contact ADS or look through the manual to wire your own. Currently,
- if you compile with 16bit mode support and switch into a lower bpp
- mode, the timing is off so the image is corrupted. This will be
- fixed soon.
-
-Any contribution can be sent to nico@fluxnic.net and will be greatly welcome!
diff --git a/Documentation/arm/sa1100/huw_webpanel.rst b/Documentation/arm/sa1100/huw_webpanel.rst
deleted file mode 100644
index 1dc7ccb165f0..000000000000
--- a/Documentation/arm/sa1100/huw_webpanel.rst
+++ /dev/null
@@ -1,21 +0,0 @@
-=======================
-Hoeft & Wessel Webpanel
-=======================
-
-The HUW_WEBPANEL is a product of the german company Hoeft & Wessel AG
-
-If you want more information, please visit
-http://www.hoeft-wessel.de
-
-To build the kernel::
-
- make huw_webpanel_config
- make oldconfig
- [accept all defaults]
- make zImage
-
-Mostly of the work is done by:
-Roman Jordan jor@hoeft-wessel.de
-Christoph Schulz schu@hoeft-wessel.de
-
-2000/12/18/
diff --git a/Documentation/arm/sa1100/index.rst b/Documentation/arm/sa1100/index.rst
index 68c2a280a745..c9aed43280ff 100644
--- a/Documentation/arm/sa1100/index.rst
+++ b/Documentation/arm/sa1100/index.rst
@@ -7,19 +7,7 @@ Intel StrongARM 1100
.. toctree::
:maxdepth: 1

- adsbitsy
assabet
- brutus
cerf
- freebird
- graphicsclient
- graphicsmaster
- huw_webpanel
- itsy
lart
- nanoengine
- pangolin
- pleb
serial_uart
- tifon
- yopy
diff --git a/Documentation/arm/sa1100/itsy.rst b/Documentation/arm/sa1100/itsy.rst
deleted file mode 100644
index f49896ba3ef1..000000000000
--- a/Documentation/arm/sa1100/itsy.rst
+++ /dev/null
@@ -1,47 +0,0 @@
-====
-Itsy
-====
-
-Itsy is a research project done by the Western Research Lab, and Systems
-Research Center in Palo Alto, CA. The Itsy project is one of several
-research projects at Compaq that are related to pocket computing.
-
-For more information, see:
-
- http://www.hpl.hp.com/downloads/crl/itsy/
-
-Notes on initial 2.4 Itsy support (8/27/2000) :
-
-The port was done on an Itsy version 1.5 machine with a daughtercard with
-64 Meg of DRAM and 32 Meg of Flash. The initial work includes support for
-serial console (to see what you're doing). No other devices have been
-enabled.
-
-To build, do a "make menuconfig" (or xmenuconfig) and select Itsy support.
-Disable Flash and LCD support. and then do a make zImage.
-Finally, you will need to cd to arch/arm/boot/tools and execute a make there
-to build the params-itsy program used to boot the kernel.
-
-In order to install the port of 2.4 to the itsy, You will need to set the
-configuration parameters in the monitor as follows::
-
- Arg 1:0x08340000, Arg2: 0xC0000000, Arg3:18 (0x12), Arg4:0
-
-Make sure the start-routine address is set to 0x00060000.
-
-Next, flash the params-itsy program to 0x00060000 ("p 1 0x00060000" in the
-flash menu) Flash the kernel in arch/arm/boot/zImage into 0x08340000
-("p 1 0x00340000"). Finally flash an initial ramdisk into 0xC8000000
-("p 2 0x0") We used ramdisk-2-30.gz from the 0.11 version directory on
-handhelds.org.
-
-The serial connection we established was at:
-
-8-bit data, no parity, 1 stop bit(s), 115200.00 b/s. in the monitor, in the
-params-itsy program, and in the kernel itself. This can be changed, but
-not easily. The monitor parameters are easily changed, the params program
-setup is assembly outl's, and the kernel is a configuration item specific to
-the itsy. (i.e. grep for CONFIG_SA1100_ITSY and you'll find where it is.)
-
-
-This should get you a properly booting 2.4 kernel on the itsy.
diff --git a/Documentation/arm/sa1100/nanoengine.rst b/Documentation/arm/sa1100/nanoengine.rst
deleted file mode 100644
index 47f1a14cf98a..000000000000
--- a/Documentation/arm/sa1100/nanoengine.rst
+++ /dev/null
@@ -1,11 +0,0 @@
-==========
-nanoEngine
-==========
-
-"nanoEngine" is a SA1110 based single board computer from
-Bright Star Engineering Inc. See www.brightstareng.com/arm
-for more info.
-(Ref: Stuart Adams <sja@brightstareng.com>)
-
-Also visit Larry Doolittle's "Linux for the nanoEngine" site:
-http://www.brightstareng.com/arm/nanoeng.htm
diff --git a/Documentation/arm/sa1100/pangolin.rst b/Documentation/arm/sa1100/pangolin.rst
deleted file mode 100644
index f0c5c1618553..000000000000
--- a/Documentation/arm/sa1100/pangolin.rst
+++ /dev/null
@@ -1,29 +0,0 @@
-========
-Pangolin
-========
-
-Pangolin is a StrongARM 1110-based evaluation platform produced
-by Dialogue Technology (http://www.dialogue.com.tw/).
-It has EISA slots for ease of configuration with SDRAM/Flash
-memory card, USB/Serial/Audio card, Compact Flash card,
-PCMCIA/IDE card and TFT-LCD card.
-
-To compile for Pangolin, you must issue the following commands::
-
- make pangolin_config
- make oldconfig
- make zImage
-
-Supported peripherals
-=====================
-
-- SA1110 serial port (UART1/UART2/UART3)
-- flash memory access
-- compact flash driver
-- UDA1341 sound driver
-- SA1100 LCD controller for 800x600 16bpp TFT-LCD
-- MQ-200 driver for 800x600 16bpp TFT-LCD
-- Penmount(touch panel) driver
-- PCMCIA driver
-- SMC91C94 LAN driver
-- IDE driver (experimental)
diff --git a/Documentation/arm/sa1100/pleb.rst b/Documentation/arm/sa1100/pleb.rst
deleted file mode 100644
index d5b732967aa3..000000000000
--- a/Documentation/arm/sa1100/pleb.rst
+++ /dev/null
@@ -1,13 +0,0 @@
-====
-PLEB
-====
-
-The PLEB project was started as a student initiative at the School of
-Computer Science and Engineering, University of New South Wales to make a
-pocket computer capable of running the Linux Kernel.
-
-PLEB support has yet to be fully integrated.
-
-For more information, see:
-
- http://www.cse.unsw.edu.au
diff --git a/Documentation/arm/sa1100/tifon.rst b/Documentation/arm/sa1100/tifon.rst
deleted file mode 100644
index c26e910b9ea7..000000000000
--- a/Documentation/arm/sa1100/tifon.rst
+++ /dev/null
@@ -1,7 +0,0 @@
-=====
-Tifon
-=====
-
-More info has to come...
-
-Contact: Peter Danielsson <peter.danielsson@era-t.ericsson.se>
diff --git a/Documentation/arm/sa1100/yopy.rst b/Documentation/arm/sa1100/yopy.rst
deleted file mode 100644
index 5b35a5f61a44..000000000000
--- a/Documentation/arm/sa1100/yopy.rst
+++ /dev/null
@@ -1,5 +0,0 @@
-====
-Yopy
-====
-
-See http://www.yopydeveloper.org for more.
--
2.20.1
\
 
 \ /
  Last update: 2019-08-08 19:00    [W:0.553 / U:0.692 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site