lkml.org 
[lkml]   [2019]   [Aug]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH net] net: phy: rtl8211f: do a double read to get real time link status
From
Date


On 2019/8/8 0:47, Heiner Kallweit wrote:
> On 07.08.2019 15:16, Yonglong Liu wrote:
>> [ 27.232781] hns3 0000:bd:00.3 eth7: net open
>> [ 27.237303] 8021q: adding VLAN 0 to HW filter on device eth7
>> [ 27.242972] IPv6: ADDRCONF(NETDEV_CHANGE): eth7: link becomes ready
>> [ 27.244449] hns3 0000:bd:00.3: invalid speed (-1)
>> [ 27.253904] hns3 0000:bd:00.3 eth7: failed to adjust link.
>> [ 27.259379] RTL8211F Gigabit Ethernet mii-0000:bd:00.3:07: PHY state change UP -> RUNNING
>> [ 27.924903] hns3 0000:bd:00.3 eth7: link up
>> [ 28.280479] RTL8211F Gigabit Ethernet mii-0000:bd:00.3:07: PHY state change RUNNING -> NOLINK
>> [ 29.208452] hns3 0000:bd:00.3 eth7: link down
>> [ 32.376745] RTL8211F Gigabit Ethernet mii-0000:bd:00.3:07: PHY state change NOLINK -> RUNNING
>> [ 33.208448] hns3 0000:bd:00.3 eth7: link up
>> [ 35.253821] hns3 0000:bd:00.3 eth7: net stop
>> [ 35.258270] hns3 0000:bd:00.3 eth7: link down
>>
>> When using rtl8211f in polling mode, may get a invalid speed,
>> because of reading a fake link up and autoneg complete status
>> immediately after starting autoneg:
>>
>> ifconfig-1176 [007] .... 27.232763: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x00 val:0x1040
>> kworker/u257:1-670 [015] .... 27.232805: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x04 val:0x01e1
>> kworker/u257:1-670 [015] .... 27.232815: mdio_access: mii-0000:bd:00.3 write phy:0x07 reg:0x04 val:0x05e1
>> kworker/u257:1-670 [015] .... 27.232869: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x01 val:0x79ad
>> kworker/u257:1-670 [015] .... 27.232904: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x09 val:0x0200
>> kworker/u257:1-670 [015] .... 27.232940: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x00 val:0x1040
>> kworker/u257:1-670 [015] .... 27.232949: mdio_access: mii-0000:bd:00.3 write phy:0x07 reg:0x00 val:0x1240
>> kworker/u257:1-670 [015] .... 27.233003: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x01 val:0x79ad
>> kworker/u257:1-670 [015] .... 27.233039: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x0a val:0x3002
>> kworker/u257:1-670 [015] .... 27.233074: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x09 val:0x0200
>> kworker/u257:1-670 [015] .... 27.233110: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x05 val:0x0000
>> kworker/u257:1-670 [000] .... 28.280475: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x01 val:0x7989
>> kworker/u257:1-670 [000] .... 29.304471: mdio_access: mii-0000:bd:00.3 read phy:0x07 reg:0x01 val:0x7989
>>
>> According to the datasheet of rtl8211f, to get the real time
>> link status, need to read MII_BMSR twice.
>>
>> This patch add a read_status hook for rtl8211f, and do a fake
>> phy_read before genphy_read_status(), so that can get real link
>> status in genphy_read_status().
>>
>> Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
>> ---
>> drivers/net/phy/realtek.c | 13 +++++++++++++
>> 1 file changed, 13 insertions(+)
>>
> Is this an accidental resubmit? Because we discussed this in
> https://marc.info/?t=156413509900003&r=1&w=2 and a fix has
> been applied already.
>
> Heiner
>
> .
>

In https://marc.info/?t=156413509900003&r=1&w=2 , the invalid speed
recurrence rate is almost 100%, and I had test the solution about
5 times and it works. But yesterday it happen again suddenly, and than
I fount that the recurrence rate reduce to 10%. This time we get 0x79ad
after autoneg started which is not 0x798d from last discussion.


\
 
 \ /
  Last update: 2019-08-08 03:17    [W:0.070 / U:0.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site