lkml.org 
[lkml]   [2019]   [Aug]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 3/3] HID: intel-ish-hid: ipc: check the NO_D3 flag to distinguish resume paths
Date
The NO_D3 flag would be set if the ISH enter D0i3 in ish_suspend(),
The resume paths can be distinguished by checking the NO_D3 flag.
It's more reasonable than checking the FW status.

Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
---
drivers/hid/intel-ish-hid/ipc/pci-ish.c | 34 +++++++++++--------------
1 file changed, 15 insertions(+), 19 deletions(-)

diff --git a/drivers/hid/intel-ish-hid/ipc/pci-ish.c b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
index 35081f2cf781..f269852304e5 100644
--- a/drivers/hid/intel-ish-hid/ipc/pci-ish.c
+++ b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
@@ -210,19 +210,11 @@ static void __maybe_unused ish_resume_handler(struct work_struct *work)
{
struct pci_dev *pdev = to_pci_dev(ish_resume_device);
struct ishtp_device *dev = pci_get_drvdata(pdev);
- uint32_t fwsts;
int ret;

- pdev->dev_flags &= ~PCI_DEV_FLAGS_NO_D3;
-
- /* Get ISH FW status */
- fwsts = IPC_GET_ISH_FWSTS(dev->ops->get_fw_status(dev));
-
- /*
- * If currently, in ISH FW, sensor app is loaded or beyond that,
- * it means ISH isn't powered off, in this case, send a resume message.
- */
- if (fwsts >= FWSTS_SENSOR_APP_LOADED) {
+ /* Check the NO_D3 flag to distinguish the resume paths */
+ if (pdev->dev_flags & PCI_DEV_FLAGS_NO_D3) {
+ pdev->dev_flags &= ~PCI_DEV_FLAGS_NO_D3;
disable_irq_wake(pdev->irq);

ishtp_send_resume(dev);
@@ -232,16 +224,20 @@ static void __maybe_unused ish_resume_handler(struct work_struct *work)
ret = wait_event_interruptible_timeout(dev->resume_wait,
!dev->resume_flag,
msecs_to_jiffies(WAIT_FOR_RESUME_ACK_MS));
- }

- /*
- * If in ISH FW, sensor app isn't loaded yet, or no resume response.
- * That means this platform is not S0ix compatible, or something is
- * wrong with ISH FW. So on resume, full reboot of ISH processor will
- * happen, so need to go through init sequence again.
- */
- if (dev->resume_flag)
+ /*
+ * If the flag is not cleared, something is wrong with ISH FW.
+ * So on resume, need to go through init sequence again.
+ */
+ if (dev->resume_flag)
+ ish_init(dev);
+ } else {
+ /*
+ * Resume from the D3, full reboot of ISH processor will happen,
+ * so need to go through init sequence again.
+ */
ish_init(dev);
+ }
}

/**
--
2.17.1
\
 
 \ /
  Last update: 2019-08-08 04:25    [W:0.068 / U:0.288 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site