lkml.org 
[lkml]   [2019]   [Aug]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 14/22] ARM: omap1: use pci_ioremap_io() for omap_cf
Hi,

On Wed, Aug 28, 2019 at 03:02:36PM +0200, Arnd Bergmann wrote:
> On Tue, Aug 27, 2019 at 9:05 PM Aaro Koskinen <aaro.koskinen@iki.fi> wrote:
> > On Tue, Aug 27, 2019 at 06:33:01PM +0200, Arnd Bergmann wrote:
> > > On Fri, Aug 16, 2019 at 10:34 AM Aaro Koskinen <aaro.koskinen@iki.fi> wrote:
> > > > However with earlyprintk it seems to hang as soon as kernel tries to print
> > > > something. So something goes wrong with early DEBUG_LL mapping code when
> > > > CONFIG_DEBUG_UART_VIRT=0xff000000 is used?
> > >
> > > I just redid the calculation and came out with the same address, so I
> > > don't think I put the wrong one there. The address also does not
> > > conflict with the PCI mapping, and the address is the same one that
> > > is installed later, so that should also be fine.
> > >
> > > Are you sure you used the correct address in the .config file? If you
> > > ran 'make oldconfig', the virtual address would not be changed here
> > > as I just modify the default for a fresh 'make omap1_defconfig'
> > > run or similar.
> >
> > Yes... You should be able to try this out also in QEMU to see the hang:
>
> Haven't tried yet, but I took a look at the dump:
>
> > $ qemu-system-arm -M sx1 -kernel sx1-zImage -nographic
> >
> > [ Hangs silently, press Ctrl-a c to enter monitor. ]
> >
> > QEMU 4.1.0 monitor - type 'help' for more information
> > (qemu) info registers
> > R00=c0379de1 R01=0000005b R02=00000000 R03=ff000000
> > R04=00000000 R05=00000031 R06=c038f119 R07=00000000
> > R08=00000000 R09=c038f50e R10=600001d3 R11=00000001
> > R12=00000010 R13=c0379de0 R14=c000e07c R15=c000dfcc
> > PSR=000001d3 ---- A svc32
> > FPSCR: 00000000
> >
> > from System.map:
> > c000df7c T printascii
> > c000dfe0 T printch
>
> Ok, that is clearly the "busyloop" macro in
> arch/arm/include/debug/8250.S, checking if the data got sent.
>
> The 'r2' register contains zero, so UART_LSR_TEMT and
> UART_LSR_THRE are not set, but presumably the mapping
> was installed right since you did not get a page fault.
>
> I assume you checked that the uart output wasn't already broken
> by one of the earlier patches, right?

Correct, it's only with the mapping change patch it hangs.

> Also, looking at arch/arm/mach-omap1/include/mach/uncompress.h
> it seems that SX1 normally uses UART3, not UART1.
> Is that different in qemu?

In QEMU all uarts can be used, trying with UART3 as early console
hangs as well. (It prints Uncompressing... done. but I guess that's
done with the physical address.)

A.

\
 
 \ /
  Last update: 2019-08-28 20:25    [W:0.106 / U:1.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site