lkml.org 
[lkml]   [2019]   [Aug]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v12 3/5] dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver
Date
On 5/9/19 6:11 PM, Dan Murphy wrote:
> DT binding documentation for TI TCAN4x5x driver.
>
> Signed-off-by: Dan Murphy <dmurphy@ti.com>
> ---
>
> v12 - No changes - https://lore.kernel.org/patchwork/patch/1052300/
>
> v11 - No changes - https://lore.kernel.org/patchwork/patch/1051178/
> v10 - No changes - https://lore.kernel.org/patchwork/patch/1050488/
> v9 - No Changes - https://lore.kernel.org/patchwork/patch/1050118/
> v8 - No Changes - https://lore.kernel.org/patchwork/patch/1047981/
> v7 - Made device state optional - https://lore.kernel.org/patchwork/patch/1047218/
> v6 - No changes - https://lore.kernel.org/patchwork/patch/1042445/
>
> .../devicetree/bindings/net/can/tcan4x5x.txt | 37 +++++++++++++++++++
> 1 file changed, 37 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/can/tcan4x5x.txt
>
> diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
> new file mode 100644
> index 000000000000..c388f7d9feb1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
> @@ -0,0 +1,37 @@
> +Texas Instruments TCAN4x5x CAN Controller
> +================================================
> +
> +This file provides device node information for the TCAN4x5x interface contains.
> +
> +Required properties:
> + - compatible: "ti,tcan4x5x"
> + - reg: 0
> + - #address-cells: 1
> + - #size-cells: 0
> + - spi-max-frequency: Maximum frequency of the SPI bus the chip can
> + operate at should be less than or equal to 18 MHz.
> + - data-ready-gpios: Interrupt GPIO for data and error reporting.
> + - device-wake-gpios: Wake up GPIO to wake up the TCAN device.
> +
> +See Documentation/devicetree/bindings/net/can/m_can.txt for additional
> +required property details.
> +
> +Optional properties:
> + - reset-gpios: Hardwired output GPIO. If not defined then software
> + reset.
> + - device-state-gpios: Input GPIO that indicates if the device is in
> + a sleep state or if the device is active.
> +
> +Example:
> +tcan4x5x: tcan4x5x@0 {
> + compatible = "ti,tcan4x5x";
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <10000000>;
> + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>;
> + data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;

Can you convert this into a proper interrupt property? E.g.:

> interrupt-parent = <&gpio4>;
> interrupts = <13 0x2>;

See:
https://elixir.bootlin.com/linux/latest/source/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt#L21
https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git/tree/drivers/net/can/spi/mcp251x.c?h=mcp251x#n945

> + device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
> + device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
> +};

Marc

--
Pengutronix e.K. | Marc Kleine-Budde |
Industrial Linux Solutions | Phone: +49-231-2826-924 |
Vertretung West/Dortmund | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |

[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2019-08-16 11:38    [W:0.176 / U:1.312 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site