lkml.org 
[lkml]   [2019]   [Aug]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 10/22] arm64: dts: qcom: pm8150b: Add pon and adc nodes
From
Date
Quoting Vinod Koul (2019-08-14 05:50:00)
> Add the pon and adc nodes found in pm8150b PMIC.
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> arch/arm64/boot/dts/qcom/pm8150b.dtsi | 54 +++++++++++++++++++++++++++
> 1 file changed, 54 insertions(+)

Squash?

>
> diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
> index c0a678b0f159..846197bd65cd 100644
> --- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
> @@ -2,6 +2,7 @@
> // Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
> // Copyright (c) 2019, Linaro Limited
>
> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/spmi/spmi.h>
>
> @@ -11,6 +12,59 @@
> reg = <0x2 SPMI_USID>;
> #address-cells = <1>;
> #size-cells = <0>;
> +
> + pon@800 {

Maybe pon node name should be 'key' or 'power-on'?

> + compatible = "qcom,pm8916-pon";
> + reg = <0x0800>;
> + };
> +
> + adc@3100 {
> + compatible = "qcom,spmi-adc5";
> + reg = <0x3100>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #io-channel-cells = <1>;
> + interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> +
> + ref-gnd@0 {
> + reg = <ADC5_REF_GND>;
> + qcom,pre-scaling = <1 1>;
> + label = "ref_gnd";
> + };
> +
> + vref-1p25@1 {
> + reg = <ADC5_1P25VREF>;
> + qcom,pre-scaling = <1 1>;
> + label = "vref_1p25";
> + };
> +
> + die-temp@6 {
> + reg = <ADC5_DIE_TEMP>;
> + qcom,pre-scaling = <1 1>;
> + label = "die_temp";
> + };
> +
> + chg-temp@9 {
> + reg = <ADC5_CHG_TEMP>;
> + qcom,pre-scaling = <1 1>;
> + label = "chg_temp";
> + };
> +
> + smb1390-therm@14 {
> + reg = <ADC5_AMUX_THM2>;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + label = "smb1390_therm";
> + };
> +
> + smb1355-therm@78 {
> + reg = <ADC5_AMUX_THM2_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + label = "smb1355_therm";
> + };

Again, are these board level details? Maybe should be provided here with
status = "disabled" and then added by the boards that use these ADCs.

> + };
> };

\
 
 \ /
  Last update: 2019-08-14 19:10    [W:0.149 / U:3.064 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site