lkml.org 
[lkml]   [2019]   [Jul]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [v4 1/6] dt-bindings: media: Document bindings for DW MIPI CSI-2 Host
Date
Hi Sakari,

Thank you for your feedback.
I have my comments inline.

From: Sakari Ailus <sakari.ailus@iki.fi>
Date: Fri, Jun 28, 2019 at 15:13:26

> Hi Luis,
>
> Thank you for the patchset.
>
> On Tue, Jun 11, 2019 at 09:20:50PM +0200, Luis Oliveira wrote:
> > From: Luis Oliveira <lolivei@synopsys.com>
> >
> > Add bindings for Synopsys DesignWare MIPI CSI-2 host.
> >
> > Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
> > ---
> > Changelog
> > v3-v4
> > - remove "plat" from the block name @rob @laurent
> > - remove "phy-names" when single-entry @rob
> > - remove "snps,output-type" -> went to the driver config @laurent
> >
> > .../devicetree/bindings/media/snps,dw-csi.txt | 41 ++++++++++++++++++++++
> > 1 file changed, 41 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/snps,dw-csi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/snps,dw-csi.txt b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
> > new file mode 100644
> > index 0000000..613b7f9
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
> > @@ -0,0 +1,41 @@
> > +Synopsys DesignWare CSI-2 Host controller
> > +
> > +Description
> > +-----------
> > +
> > +This HW block is used to receive image coming from an MIPI CSI-2 compatible
> > +camera.
> > +
> > +Required properties:
> > +- compatible : shall be "snps,dw-csi"
> > +- reg : physical base address and size of the device memory
> > + mapped registers;
> > +- interrupts : DW CSI-2 Host interrupts
> > +- phys : List of one PHY specifier (as defined in
> > + Documentation/devicetree/bindings/phy/phy-bindings.txt).
> > + This PHY is a MIPI DPHY working in RX mode.
> > +- resets : Reference to a reset controller (optional)
> > +
> > +The per-board settings:
> > + - port sub-node describing a single endpoint connected to the camera as
> > + described in video-interfaces.txt[1].
>
> Which endpoint properties in video-interfaces.txt are relevant for the
> hardware? Which values may they have?
>

Currently I'm using only two properties "data-lanes" and "bus-width", but
I have plans to add blanking info also.
I will add more info.

> > +
> > +Example:
> > +
> > + csi2: csi2@3000 {
> > + compatible = "snps,dw-csi";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = < 0x03000 0x7FF>;
>
> reg = <0x03000 0x7FF>;

Yes, I've missed that.

>
> > + phys = <&mipi_dphy_rx>;
> > + resets = <&dw_rst 1>;
> > + interrupts = <2>;
> > +
> > + port@0 {
> > + reg = <0>;
>
> You can drop "@0" and the reg property.

Ok thank you.
>
> > + csi_ep1: endpoint {
> > + remote-endpoint = <&camera_1>;
> > + data-lanes = <1 2>;
> > + };
> > + };
> > + };
>
> --
> Kind regards,
>
> Sakari Ailus

Best regards,
Luis

\
 
 \ /
  Last update: 2019-07-08 18:15    [W:0.125 / U:0.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site