lkml.org 
[lkml]   [2019]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH AUTOSEL 4.14 086/105] PCI / ACPI: Use cached ACPI device state to get PCI device power state
From
Date
On 7/15/2019 4:28 PM, Sasha Levin wrote:
> From: Mika Westerberg <mika.westerberg@linux.intel.com>
>
> [ Upstream commit 83a16e3f6d70da99896c7a2639c0b60fff13afb8 ]
>
> The ACPI power state returned by acpi_device_get_power() may depend on
> the configuration of ACPI power resources in the system which may change
> any time after acpi_device_get_power() has returned, unless the
> reference counters of the ACPI power resources in question are set to
> prevent that from happening. Thus it is invalid to use acpi_device_get_power()
> in acpi_pci_get_power_state() the way it is done now and the value of
> the ->power.state field in the corresponding struct acpi_device objects
> (which reflects the ACPI power resources reference counting, among other
> things) should be used instead.
>
> As an example where this becomes an issue is Intel Ice Lake where the
> Thunderbolt controller (NHI), two PCIe root ports (RP0 and RP1) and xHCI
> all share the same power resources. The following picture with power
> resources marked with [] shows the topology:
>
> Host bridge
> |
> +- RP0 ---\
> +- RP1 ---|--+--> [TBT]
> +- NHI --/ |
> | |
> | v
> +- xHCI --> [D3C]
>
> Here TBT and D3C are the shared ACPI power resources. ACPI _PR3() method
> of the devices in question returns either TBT or D3C or both.
>
> Say we runtime suspend first the root ports RP0 and RP1, then NHI. Now
> since the TBT power resource is still on when the root ports are runtime
> suspended their dev->current_state is set to D3hot. When NHI is runtime
> suspended TBT is finally turned off but state of the root ports remain
> to be D3hot. Now when the xHCI is runtime suspended D3C gets also turned
> off. PCI core thus has power states of these devices cached in their
> dev->current_state as follows:
>
> RP0 -> D3hot
> RP1 -> D3hot
> NHI -> D3cold
> xHCI -> D3cold
>
> If the user now runs lspci for instance, the result is all 1's like in
> the below output (00:07.0 is the first root port, RP0):
>
> 00:07.0 PCI bridge: Intel Corporation Device 8a1d (rev ff) (prog-if ff)
> !!! Unknown header type 7f
> Kernel driver in use: pcieport
>
> In short the hardware state is not in sync with the software state
> anymore. The exact same thing happens with the PME polling thread which
> ends up bringing the root ports back into D0 after they are runtime
> suspended.
>
> For this reason, modify acpi_pci_get_power_state() so that it uses the
> ACPI device power state that was cached by the ACPI core. This makes the
> PCI device power state match the ACPI device power state regardless of
> state of the shared power resources which may still be on at this point.
>
> Link: https://lore.kernel.org/r/20190618161858.77834-2-mika.westerberg@linux.intel.com
> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
> Signed-off-by: Sasha Levin <sashal@kernel.org>
> ---
> drivers/pci/pci-acpi.c | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
> index a3cedf8de863..688e195e85b4 100644
> --- a/drivers/pci/pci-acpi.c
> +++ b/drivers/pci/pci-acpi.c
> @@ -563,7 +563,8 @@ static pci_power_t acpi_pci_get_power_state(struct pci_dev *dev)
> if (!adev || !acpi_device_power_manageable(adev))
> return PCI_UNKNOWN;
>
> - if (acpi_device_get_power(adev, &state) || state == ACPI_STATE_UNKNOWN)
> + state = adev->power.state;
> + if (state == ACPI_STATE_UNKNOWN)
> return PCI_UNKNOWN;
>
> return state_conv[state];

This requires additional changes to really work in all cases, please do
not include it alone into -stable.


\
 
 \ /
  Last update: 2019-07-16 11:23    [W:0.355 / U:1.252 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site