lkml.org 
[lkml]   [2019]   [Jun]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [RFC next v1 5/5] arm64: dts: meson: g12a: x96-max: fix the Ethernet PHY reset line
Hi Linus,

On Mon, Jun 10, 2019 at 12:06 AM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Sun, Jun 9, 2019 at 11:36 PM Martin Blumenstingl
> <martin.blumenstingl@googlemail.com> wrote:
>
> > > If "snps,reset-active-low" was set it results in the sequence 1, 0, 1
> > > if it is not set it results in the sequence 0, 1, 0.
> >
> > I'm changing this logic with earlier patches of this series.
> > can you please look at these as well because GPIO_OPEN_SOURCE doesn't
> > work with the old version of stmmac_mdio_reset() that you are showing.
>
> OK but the logic is the same, just that the polarity handling is moved
> into gpiolib.
>
> > > The high (reset) is asserted by switching the pin into high-z open drain
> > > mode, which happens by switching the line into input mode in some
> > > cases.
> > >
> > > I think the real reason it works now is that reset is actually active high.
> >
> > let me write down what I definitely know so far
> >
> > the RTL8211F PHY wants the reset line to be LOW for a few milliseconds
> > to put it into reset mode.
> > driving the reset line HIGH again takes it out of reset.
> >
> > Odroid-N2's schematics [0] (page 30) shows that there's a pull-up for
> > the PHYRSTB pin, which is also connected to the NRST signal which is
> > GPIOZ_15
>
> Looks correct, R143 is indeed a pull up indicating that the line is
> open drain, active low.
good so far

> > > It makes a lot of sense, since if it resets the device when set as input
> > > (open drain) it holds all devices on that line in reset, which is likely
> > > what you want as most GPIOs come up as inputs (open drain).
> > > A pull-up resistor will ascertain that the devices are in reset.
> >
> > my understanding is that the pull-up resistor holds it out of reset
> > driving GPIOZ_15's (open drain) output LOW pulls the signal to ground
> > and asserts the reset
>
> Yep that seems correct.
>
> Oh I guess it is this:
>
> amlogic,tx-delay-ns = <2>;
> - snps,reset-gpio = <&gpio GPIOZ_14 0>;
> + snps,reset-gpio = <&gpio GPIOZ_15 GPIO_OPEN_SOURCE>;
> snps,reset-delays-us = <0 10000 1000000>;
> - snps,reset-active-low;
>
> Can you try:
> snps,reset-gpio = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
> ?
I tried it and it works!

> Open source is nominally (and rarely) used for lines that are active high.
> For lines that are active low, we want to use open drain combined
> with active low.
thank you for the explanation - I'll take your version for v2 :)


Martin

\
 
 \ /
  Last update: 2019-06-10 00:30    [W:0.092 / U:29.592 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site