lkml.org 
[lkml]   [2019]   [Jun]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v8 08/13] drivers: memory: add DMC driver for Exynos5422
From
Date
On 6/6/19 1:45 PM, Krzysztof Kozlowski wrote:
> On Thu, 6 Jun 2019 at 12:38, Lukasz Luba <l.luba@partner.samsung.com> wrote:
>> Hi Krzysztof,
>>>> +/**
>>>> + * exynos5_dmc_init_clks() - Initialize clocks needed for DMC operation.
>>>> + * @dmc: DMC structure containing needed fields
>>>> + *
>>>> + * Get the needed clocks defined in DT device, enable and set the right parents.
>>>> + * Read current frequency and initialize the initial rate for governor.
>>>> + */
>>>> +static int exynos5_dmc_init_clks(struct exynos5_dmc *dmc)
>>>> +{
>>>> + int ret;
>>>> + unsigned long target_volt = 0;
>>>> + unsigned long target_rate = 0;
>>>> +
>>>> + dmc->fout_spll = devm_clk_get(dmc->dev, "fout_spll");
>>>> + if (IS_ERR(dmc->fout_spll))
>>>> + return PTR_ERR(dmc->fout_spll);
>>>> +
>>>> + dmc->fout_bpll = devm_clk_get(dmc->dev, "fout_bpll");
>>>> + if (IS_ERR(dmc->fout_bpll))
>>>> + return PTR_ERR(dmc->fout_bpll);
>>>> +
>>>> + dmc->mout_mclk_cdrex = devm_clk_get(dmc->dev, "mout_mclk_cdrex");
>>>> + if (IS_ERR(dmc->mout_mclk_cdrex))
>>>> + return PTR_ERR(dmc->mout_mclk_cdrex);
>>>
>>> You are not enabling this clock. It is divider so it is fine for him
>>> but what about its parents? How can you guarantee that parents are
>>> enabled?
>> It uses two parents in this configuration:
>> 1. 'mout_bpll' which is set by the bootloader and is a default mode
>> 2. 'mout_mx_mspll_ccore' which is used temporary as a 'bypass clock
>> source' only for the time when BPLL is changing it's settings
>>
>> Do you suggest to put a call:
>>
>> to make sure the parent is up and running?
>> OR just move the lines from the end of this function:
>> clk_prepare_enable(dmc->fout_bpll);
>> clk_prepare_enable(dmc->mout_bpll);
>> and add:
>> ret = clk_set_parent(dmc->mout_mclk_cdrex, dmc->mout_bpll);
>> then call the clk_get_rate on 'mout_mclk_cdrex'
>>
>
> Ah, It's my mistake. I missed that later you enable its new parent. It's fine.
OK, so I will leave it as is and just fix the other stuff that you've
mentioned.

Regards,
Lukasz
>
> Best regards,
> Krzysztof
>
>

\
 
 \ /
  Last update: 2019-06-06 15:35    [W:0.096 / U:4.764 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site