lkml.org 
[lkml]   [2019]   [Jun]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 5.2 v2 1/2] edac: npcm: Add Nuvoton NPCM7xx EDAC driver
On Wed, Jun 5, 2019 at 5:18 PM George Hung <ghung.quanta@gmail.com> wrote:
>
> Add support for the Nuvoton NPCM7xx SoC EDAC driver
>
> NPCM7xx ECC datasheet from nuvoton.israel-Poleg:
> "Cadence DDR Controller User’s Manual For DDR3 & DDR4 Memories"
>
> Tested: Forcing an ECC error event
>
> Write a value to the xor_check_bits parameter that will trigger
> an ECC event once that word is read
>
> For example, to force a single-bit correctable error on bit 0 of
> the user-word space shown, write 0x75 into that byte of the
> xor_check_bits parameter and then assert fwc (force write check)
> bit to 'b1' (mem base: 0xf0824000, xor_check_bits reg addr: 0x178)
>
> $ devmem 0xf0824178 32 0x7501
>
> To force a double-bit un-correctable error for the user-word space,
> write 0x03 into that byte of the xor_check_bits parameter
>
> $ devmem 0xf0824178 32 0x301
>
> Signed-off-by: George Hung <ghung.quanta@gmail.com>

Reviewed-by: Avi Fishman <avifishman70@gmail.com>

> ---
> MAINTAINERS | 6 +
> drivers/edac/Kconfig | 7 +
> drivers/edac/Makefile | 1 +
> drivers/edac/npcm7xx_edac.c | 424 ++++++++++++++++++++++++++++++++++++
> 4 files changed, 438 insertions(+)
> create mode 100644 drivers/edac/npcm7xx_edac.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index a6954776a37e..9faf7a48eea2 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -5784,6 +5784,12 @@ L: linux-edac@vger.kernel.org
> S: Maintained
> F: drivers/edac/mpc85xx_edac.[ch]
>
> +EDAC-NPCM7XX
> +M: George Hung <george.hung@quantatw.com>
> +S: Maintained
> +F: drivers/edac/npcm7xx_edac.c
> +F: Documentation/devicetree/bindings/edac/npcm7xx-sdram-edac.txt
> +
> EDAC-PASEMI
> M: Egor Martovetsky <egor@pasemi.com>
> L: linux-edac@vger.kernel.org
> diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
> index 5e2e0348d460..d8834b3c9ec8 100644
> --- a/drivers/edac/Kconfig
> +++ b/drivers/edac/Kconfig
> @@ -504,4 +504,11 @@ config EDAC_ASPEED
> First, ECC must be configured in the bootloader. Then, this driver
> will expose error counters via the EDAC kernel framework.
>
> +config EDAC_NPCM7XX
> + tristate "Nuvoton NPCM7xx DDR Memory Controller"
> + depends on ARCH_NPCM7XX
> + help
> + Support for error detection and correction on the
> + Nuvoton NPCM7xx DDR memory controller.
> +
> endif # EDAC
> diff --git a/drivers/edac/Makefile b/drivers/edac/Makefile
> index 89ad4a84a0f6..ae70e4c02fd9 100644
> --- a/drivers/edac/Makefile
> +++ b/drivers/edac/Makefile
> @@ -84,3 +84,4 @@ obj-$(CONFIG_EDAC_XGENE) += xgene_edac.o
> obj-$(CONFIG_EDAC_TI) += ti_edac.o
> obj-$(CONFIG_EDAC_QCOM) += qcom_edac.o
> obj-$(CONFIG_EDAC_ASPEED) += aspeed_edac.o
> +obj-$(CONFIG_EDAC_NPCM7XX) += npcm7xx_edac.o
> diff --git a/drivers/edac/npcm7xx_edac.c b/drivers/edac/npcm7xx_edac.c
> new file mode 100644
> index 000000000000..2d2deb81e49c
> --- /dev/null
> +++ b/drivers/edac/npcm7xx_edac.c
> @@ -0,0 +1,424 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019 Quanta Computer lnc.
> + */
> +
> +#include <linux/edac.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +
> +#include "edac_module.h"
> +
> +#define ECC_ENABLE BIT(24)
> +#define ECC_EN_INT_MASK 0x7fffff87
> +
> +#define INT_STATUS_ADDR 116
> +#define INT_ACK_ADDR 117
> +#define INT_MASK_ADDR 118
> +
> +#define ECC_EN_ADDR 93
> +#define ECC_C_ADDR_ADDR 98
> +#define ECC_C_DATA_ADDR 100
> +#define ECC_C_ID_ADDR 101
> +#define ECC_C_SYND_ADDR 99
> +#define ECC_U_ADDR_ADDR 95
> +#define ECC_U_DATA_ADDR 97
> +#define ECC_U_ID_ADDR 101
> +#define ECC_U_SYND_ADDR 96
> +
> +#define ECC_ERROR -1
> +#define EDAC_MSG_SIZE 256
> +#define EDAC_MOD_NAME "npcm7xx-edac"
> +
> +struct ecc_error_signature_info {
> + u32 ecc_addr;
> + u32 ecc_data;
> + u32 ecc_id;
> + u32 ecc_synd;
> +};
> +
> +struct npcm7xx_ecc_int_status {
> + u32 int_mask;
> + u32 int_status;
> + u32 int_ack;
> + u32 ce_cnt;
> + u32 ue_cnt;
> + struct ecc_error_signature_info ceinfo;
> + struct ecc_error_signature_info ueinfo;
> +};
> +
> +struct npcm7xx_edac_priv {
> + void __iomem *baseaddr;
> + char message[EDAC_MSG_SIZE];
> + struct npcm7xx_ecc_int_status stat;
> +};
> +
> +/**
> + * npcm7xx_edac_get_ecc_syndrom - Get the current ecc error info
> + * @base: Pointer to the base address of the ddr memory controller
> + * @p: Pointer to the Nuvoton ecc status structure
> + *
> + * Determines there is any ecc error or not
> + *
> + * Return: ECC detection status
> + */
> +static int npcm7xx_edac_get_ecc_syndrom(void __iomem *base,
> + struct npcm7xx_ecc_int_status *p)
> +{
> + int status = 0;
> + u32 int_status = 0;
> +
> + int_status = readl(base + 4*INT_STATUS_ADDR);
> + writel(int_status, base + 4*INT_ACK_ADDR);
> + edac_dbg(3, "int_status: %#08x\n", int_status);
> +
> + if ((int_status & (1 << 6)) == (1 << 6)) {
> + edac_dbg(3, "6-Mult uncorrectable detected.\n");
> + p->ue_cnt++;
> + status = ECC_ERROR;
> + }
> +
> + if ((int_status & (1 << 5)) == (1 << 5)) {
> + edac_dbg(3, "5-An uncorrectable detected\n");
> + p->ue_cnt++;
> + status = ECC_ERROR;
> + }
> +
> + if ((int_status & (1 << 4)) == (1 << 4)) {
> + edac_dbg(3, "4-mult correctable detected.\n");
> + p->ce_cnt++;
> + status = ECC_ERROR;
> + }
> +
> + if ((int_status & (1 << 3)) == (1 << 3)) {
> + edac_dbg(3, "3-A correctable detected.\n");
> + p->ce_cnt++;
> + status = ECC_ERROR;
> + }
> +
> + if (status == ECC_ERROR) {
> + u32 ecc_id;
> +
> + p->ceinfo.ecc_addr = readl(base + 4*ECC_C_ADDR_ADDR);
> + p->ceinfo.ecc_data = readl(base + 4*ECC_C_DATA_ADDR);
> + p->ceinfo.ecc_synd = readl(base + 4*ECC_C_SYND_ADDR);
> +
> + p->ueinfo.ecc_addr = readl(base + 4*ECC_U_ADDR_ADDR);
> + p->ueinfo.ecc_data = readl(base + 4*ECC_U_DATA_ADDR);
> + p->ueinfo.ecc_synd = readl(base + 4*ECC_U_SYND_ADDR);
> +
> + /* ECC_C_ID_ADDR has same value as ECC_U_ID_ADDR */
> + ecc_id = readl(base + 4*ECC_C_ID_ADDR);
> + p->ueinfo.ecc_id = ecc_id & 0xffff;
> + p->ceinfo.ecc_id = ecc_id >> 16;
> + }
> +
> + return status;
> +}
> +
> +/**
> + * npcm7xx_edac_handle_error - Handle controller error types CE and UE
> + * @mci: Pointer to the edac memory controller instance
> + * @p: Pointer to the Nuvoton ecc status structure
> + *
> + * Handles the controller ECC correctable and un correctable error.
> + */
> +static void npcm7xx_edac_handle_error(struct mem_ctl_info *mci,
> + struct npcm7xx_ecc_int_status *p)
> +{
> + struct npcm7xx_edac_priv *priv = mci->pvt_info;
> + u32 page, offset;
> +
> + if (p->ce_cnt) {
> + snprintf(priv->message, EDAC_MSG_SIZE,
> + "DDR ECC: synd=%#08x addr=%#08x data=%#08x source_id=%#08x ",
> + p->ceinfo.ecc_synd, p->ceinfo.ecc_addr,
> + p->ceinfo.ecc_data, p->ceinfo.ecc_id);
> +
> + page = p->ceinfo.ecc_addr >> PAGE_SHIFT;
> + offset = p->ceinfo.ecc_addr & ~PAGE_MASK;
> + edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci,
> + p->ce_cnt, page, offset,
> + p->ceinfo.ecc_synd,
> + 0, 0, -1,
> + priv->message, "");
> + }
> +
> + if (p->ue_cnt) {
> + snprintf(priv->message, EDAC_MSG_SIZE,
> + "DDR ECC: synd=%#08x addr=%#08x data=%#08x source_id=%#08x ",
> + p->ueinfo.ecc_synd, p->ueinfo.ecc_addr,
> + p->ueinfo.ecc_data, p->ueinfo.ecc_id);
> +
> + page = p->ueinfo.ecc_addr >> PAGE_SHIFT;
> + offset = p->ueinfo.ecc_addr & ~PAGE_MASK;
> + edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci,
> + p->ue_cnt, page, offset,
> + p->ueinfo.ecc_synd,
> + 0, 0, -1,
> + priv->message, "");
> + }
> +
> + memset(p, 0, sizeof(*p));
> +}
> +
> +/**
> + * npcm7xx_edac_check - Check controller for ECC errors
> + * @mci: Pointer to the edac memory controller instance
> + *
> + * This routine is used to check and post ECC errors and is called by
> + * this driver's CE and UE interrupt handler.
> + */
> +static void npcm7xx_edac_check(struct mem_ctl_info *mci)
> +{
> + struct npcm7xx_edac_priv *priv = mci->pvt_info;
> + int status = 0;
> +
> + status = npcm7xx_edac_get_ecc_syndrom(priv->baseaddr, &priv->stat);
> + if (status != ECC_ERROR)
> + return;
> +
> + npcm7xx_edac_handle_error(mci, &priv->stat);
> +}
> +
> +/**
> + * npcm7xx_edac_isr - CE/UE interrupt service routine
> + * @irq: The virtual interrupt number being serviced.
> + * @dev_id: A pointer to the EDAC memory controller instance
> + * associated with the interrupt being handled.
> + *
> + * This routine implements the interrupt handler for both correctable
> + * (CE) and uncorrectable (UE) ECC errors for the Nuvoton Cadence DDR
> + * controller. It simply calls through to the routine used to check,
> + * report and clear the ECC status.
> + *
> + * Unconditionally returns IRQ_HANDLED.
> + */
> +static irqreturn_t npcm7xx_edac_isr(int irq, void *dev_id)
> +{
> + struct mem_ctl_info *mci = dev_id;
> + int npcm_edac_report = 0;
> +
> + npcm_edac_report = edac_get_report_status();
> + if (npcm_edac_report != EDAC_REPORTING_DISABLED)
> + npcm7xx_edac_check(mci);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int npcm7xx_edac_register_irq(struct mem_ctl_info *mci,
> + struct platform_device *pdev)
> +{
> + int status = 0;
> + int mc_irq;
> + struct npcm7xx_edac_priv *priv = mci->pvt_info;
> +
> + /* Only enable MC interrupts with ECC - clear int_mask[6:3] */
> + writel(ECC_EN_INT_MASK, priv->baseaddr + 4*INT_MASK_ADDR);
> +
> + mc_irq = platform_get_irq(pdev, 0);
> +
> + if (!mc_irq) {
> + edac_printk(KERN_ERR, EDAC_MC, "Unable to map interrupts.\n");
> + status = -ENODEV;
> + goto fail;
> + }
> +
> + status = devm_request_irq(&pdev->dev, mc_irq, npcm7xx_edac_isr, 0,
> + "npcm-memory-controller", mci);
> +
> + if (status < 0) {
> + edac_printk(KERN_ERR, EDAC_MC,
> + "Unable to request irq %d for ECC",
> + mc_irq);
> + status = -ENODEV;
> + goto fail;
> + }
> +
> + return 0;
> +
> +fail:
> + return status;
> +}
> +
> +static const struct of_device_id npcm7xx_edac_of_match[] = {
> + { .compatible = "nuvoton,npcm7xx-sdram-edac"},
> + { /* end of table */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, npcm7xx_edac_of_match);
> +
> +/**
> + * npcm7xx_edac_mc_init - Initialize driver instance
> + * @mci: Pointer to the edac memory controller instance
> + * @pdev: Pointer to the platform_device struct
> + *
> + * Performs initialization of the EDAC memory controller instance and
> + * related driver-private data associated with the memory controller the
> + * instance is bound to.
> + *
> + * Returns 0 if OK; otherwise, < 0 on error.
> + */
> +static int npcm7xx_edac_mc_init(struct mem_ctl_info *mci,
> + struct platform_device *pdev)
> +{
> + const struct of_device_id *id;
> +
> + id = of_match_device(npcm7xx_edac_of_match, &pdev->dev);
> + if (!id)
> + return -ENODEV;
> +
> + /* Initialize controller capabilities and configuration */
> + mci->mtype_cap = MEM_FLAG_DDR4;
> + mci->edac_ctl_cap = EDAC_FLAG_SECDED;
> + mci->edac_cap = EDAC_FLAG_SECDED;
> + mci->scrub_cap = SCRUB_FLAG_HW_SRC;
> + mci->scrub_mode = SCRUB_HW_SRC;
> + mci->ctl_name = id->compatible;
> + mci->dev_name = dev_name(&pdev->dev);
> + mci->mod_name = EDAC_MOD_NAME;
> +
> + edac_op_state = EDAC_OPSTATE_INT;
> +
> + return 0;
> +}
> +
> +/**
> + * npcm7xx_edac_get_eccstate - Return the controller ecc enable/disable status
> + * @base: Pointer to the ddr memory controller base address
> + *
> + * Get the ECC enable/disable status for the controller
> + *
> + * Return: a ecc status boolean i.e true/false - enabled/disabled.
> + */
> +static bool npcm7xx_edac_get_eccstate(void __iomem *base)
> +{
> + u32 ecc_en;
> + bool state = false;
> +
> + ecc_en = readl(base + 4*ECC_EN_ADDR);
> + if (ecc_en & ECC_ENABLE) {
> + edac_printk(KERN_INFO, EDAC_MC, "ECC reporting and correcting on. ");
> + state = true;
> + }
> +
> + return state;
> +}
> +
> +/**
> + * npcm7xx_edac_mc_probe - Check controller and bind driver
> + * @pdev: Pointer to the platform_device struct
> + *
> + * Probes a specific controller instance for binding with the driver.
> + *
> + * Return: 0 if the controller instance was successfully bound to the
> + * driver; otherwise, < 0 on error.
> + */
> +static int npcm7xx_edac_mc_probe(struct platform_device *pdev)
> +{
> + struct mem_ctl_info *mci;
> + struct edac_mc_layer layers[1];
> + struct npcm7xx_edac_priv *priv;
> + struct resource *res;
> + void __iomem *baseaddr;
> + int rc;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + baseaddr = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(baseaddr)) {
> + edac_printk(KERN_ERR, EDAC_MOD_NAME,
> + "DDR controller regs not defined\n");
> + return PTR_ERR(baseaddr);
> + }
> +
> + /*
> + * Check if ECC is enabled.
> + * If not, there is no useful monitoring that can be done
> + * for this controller.
> + */
> + if (!npcm7xx_edac_get_eccstate(baseaddr)) {
> + edac_printk(KERN_INFO, EDAC_MC, "ECC disabled\n");
> + return -ENXIO;
> + }
> +
> + /*
> + * Allocate an EDA controller instance and perform the appropriate
> + * initialization.
> + */
> + layers[0].type = EDAC_MC_LAYER_ALL_MEM;
> + layers[0].size = 1;
> +
> + mci = edac_mc_alloc(0, ARRAY_SIZE(layers), layers,
> + sizeof(struct npcm7xx_edac_priv));
> + if (!mci) {
> + edac_printk(KERN_ERR, EDAC_MC,
> + "Failed memory allocation for mc instance\n");
> + return -ENOMEM;
> + }
> +
> + mci->pdev = &pdev->dev;
> + priv = mci->pvt_info;
> + priv->baseaddr = baseaddr;
> + platform_set_drvdata(pdev, mci);
> +
> + rc = npcm7xx_edac_mc_init(mci, pdev);
> + if (rc) {
> + edac_printk(KERN_ERR, EDAC_MC,
> + "Failed to initialize instance\n");
> + goto free_edac_mc;
> + }
> +
> + /* Attempt to register it with the EDAC subsystem */
> + rc = edac_mc_add_mc(mci);
> + if (rc) {
> + edac_printk(KERN_ERR, EDAC_MC,
> + "Failed to register with EDAC core\n");
> + goto free_edac_mc;
> + }
> +
> + /* Register interrupts */
> + rc = npcm7xx_edac_register_irq(mci, pdev);
> + if (rc)
> + goto free_edac_mc;
> +
> + return 0;
> +
> +free_edac_mc:
> + edac_mc_free(mci);
> +
> + return rc;
> +}
> +
> +/**
> + * npcm7xx_edac_mc_remove - Unbind driver from controller
> + * @pdev: Pointer to the platform_device struct
> + *
> + * Return: Unconditionally 0
> + */
> +static int npcm7xx_edac_mc_remove(struct platform_device *pdev)
> +{
> + struct mem_ctl_info *mci = platform_get_drvdata(pdev);
> +
> + edac_mc_del_mc(&pdev->dev);
> + edac_mc_free(mci);
> +
> + return 0;
> +}
> +
> +static struct platform_driver npcm7xx_edac_driver = {
> + .probe = npcm7xx_edac_mc_probe,
> + .remove = npcm7xx_edac_mc_remove,
> + .driver = {
> + .name = EDAC_MOD_NAME,
> + .of_match_table = npcm7xx_edac_of_match,
> + },
> +};
> +
> +module_platform_driver(npcm7xx_edac_driver);
> +
> +MODULE_AUTHOR("Quanta Computer Inc.");
> +MODULE_DESCRIPTION("Nuvoton NPCM7xx EDAC Driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.21.0
>


--
Regards,
Avi

\
 
 \ /
  Last update: 2019-06-06 09:42    [W:0.111 / U:25.468 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site