lkml.org 
[lkml]   [2019]   [Jun]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 2/2] irqchip: al-fic: Introduce Amazon's Annapurna Labs Fabric Interrupt Controller Driver
From
Date
On 05/06/2019 15:38, Shenhar, Talel wrote:
> Thanks, will publish the fixes on v3.
>
> On 6/5/2019 3:22 PM, Marc Zyngier wrote:
>> Talel,
>>
>> On 05/06/2019 11:52, Talel Shenhar wrote:
>>> The Amazon's Annapurna Labs Fabric Interrupt Controller has 32 inputs
>>> lines. A FIC (Fabric Interrupt Controller) may be cascaded into another FIC
>> Really? :-(
>
> Cascading is used for control path events. For data path the HW is not
> cascaded (and usually even configured in MSI-X instead of wire interrupts)
>
>
>>
>> +}
>> +
>> +static int al_fic_irq_set_type(struct irq_data *data, unsigned int flow_type)
>> +{
>> + struct irq_chip_generic *gc = irq_data_get_irq_chip_data(data);
>> + struct al_fic *fic = gc->private;
>> + enum al_fic_state new_state;
>> + int ret = 0;
>> +
>> + irq_gc_lock(gc);
>> +
>> + if (!(flow_type & IRQ_TYPE_LEVEL_HIGH) &&
>> + !(flow_type & IRQ_TYPE_EDGE_RISING)) {
>> And what if this gets passed EDGE_BOTH?
>
> FIC only support two sensing modes, rising-edge and level.

Yes, I can tell. Yet, this code will let EDGE_BOTH pass through, even if
it cannot handle it.

>
>>
>>> + * This is generally fixed depending on what pieces of HW it's wired up
>>> + * to.
>>> + *
>>> + * We configure it based on the sensitivity of the first source
>>> + * being setup, and reject any subsequent attempt at configuring it in a
>>> + * different way.
>> Is that a reliable guess? It also strikes me that the DT binding doesn't
>> allow for the trigger type to be passed, meaning the individual drivers
>> have to request the trigger as part of their request_irq() call. I'd
>> rather you have a complete interrupt specifier in DT, and document the
>> various limitations of the HW.
>
> Indeed we use interrupt specifier that has the level type in it
> (dt-binding: "#interrupt-cells: must be 2.") which in turns causes to
> this irq_set_type callback.

Well, this isn't what the example in your DT binding shows.

>
> Part of the FICs are connected to hws that generate pulse (for those,
> FIC shall be configured to rising-edge-triggered) and the others to hws
> that keep the line up (for those the FIC shall be configured to
> level-triggered).
>
>>
>>> + */
>>> + if (fic->state == AL_FIC_CLEAN) {
>>> + al_fic_set_trigger(fic, gc, new_state);
>>> + } else if (fic->state != new_state) {
>>> + pr_err("fic %s state already configured to %d\n",
>>> + fic->name, fic->state);
>>> + ret = -EPERM;
>> Same as above.
>
> Those error messages are control path messages. if we return the same
> error value from here and from the previous error, how can we
> differentiate between the two error cases by looking at the log?
>
> Having informative printouts seems like a good idea for bad
> configuration cases as such, wouldn't you agree?

I completely disagree. The kernel log isn't a dumping ground for this
kind of pretty useless information. Furthermore, the irq subsystem will
also shout at you when it gets an error, so no need to add insult to injury.

If you really want to keep them around, turn them into pr_debug.

Thanks,

M.
--
Jazz is not dead. It just smells funny...

\
 
 \ /
  Last update: 2019-06-05 17:13    [W:0.112 / U:4.852 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site