Messages in this thread | | | Subject | Re: [PATCH v15 0/3] Add support for the Purism Librem5 devkit | Date | Wed, 05 Jun 2019 06:48:05 -0600 | From | Angus Ainslie <> |
| |
On 2019-06-05 03:03, Shawn Guo wrote: > On Tue, May 28, 2019 at 05:57:44AM -0700, Angus Ainslie (Purism) wrote: >> The Librem5 devkit is based on the imx8mq from NXP. This is a default >> devicetree to boot the board to a command prompt. >> >> Changes since v14: >> >> Add regulator-always-on for the SNVS regulators. >> Added pgc nodes. >> Fixed charger pre-current. > > Since Pavel was reviewing your patches, you should copy him on the new > version. Has this version addressed all his review comments? >
Sorry I had meant to include him in the CC.
I believe so but don't want to speak for him so we should see if he has anymore.
Angus
> Shawn > >> >> Changes since v13: >> >> Moved haptic motor from pwm-led to gpio-vibrator. >> Cleaned up regulator node naming. >> Whitescpace cleanup. >> Re-indent pinmux stanzas. >> Drop pwm2 node. >> Drop MAINTAINERS patch. >> >> Changes since v12: >> >> Updated patch to vendor-prefixes.yaml. >> Dropped always on from regulators. >> >> Changes since v11: >> >> Added reviewed-by tags. >> Fixed subject typo. >> >> Changes since v10: >> >> Moved MAINTAINERS entry to "ARM/FREESCALE IMX" section >> >> Changes since v9: >> >> Added a MAINTAINERS entry for arm64 imx devicetree files. >> >> Changes since v8: >> >> Fixed license comment. >> Changed regulators to all lower case. >> Changed clock frequency for NXP errata e7805. >> Dropped blank line. >> >> Changes since v7: >> >> More regulators always on for USB. >> Add vbus regulator. >> Drop vbat regulator. >> Replace legacy "gpio-key,wakeup" with "wakeup-source". >> Add vbus-supply to get rid of warning >> imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply vbus not >> found, >> using dummy regulator >> >> Changes since v6: >> >> Dropped unused regulators. >> Fix regulator phandles case. >> Dropped extra whitespace. >> >> Changes since v5: >> >> Added reviewed-by tags. >> Moved USB port links to USB controller node. >> >> Changes since v4: >> >> Compiled against linux-next next-20190415. >> Added imx8mq to the arm yaml file. >> Re-arrange regulator nodes to drop undefined supplies. >> Additional ordering for aesthetics. >> Split some long lines. >> Added lots of blank lines. >> Moved pinctl muxes to where they are used. >> Cleaned out reg defintions from regulator nodes. >> >> Changes since v3: >> >> Freshly sorted and pressed nodes. >> Change the backlight to an interpolated scale. >> Dropped i2c2. >> Dropped devkit version number to match debian MR. >> >> Changes since v2: >> >> Fixed incorrect phy-supply for the fsl-fec. >> Dropped unused regulator property. >> Fixup Makefile for linux-next. >> >> Changes since v1: >> >> Dropped config file. >> Updated the board compatible label. >> Changed node names to follow naming conventions. >> Added a more complete regulator hierachy. >> Removed unused nodes. >> Removed unknown devices. >> Fixed comment style. >> Dropped undocumented properties. >> >> Angus Ainslie (Purism) (3): >> arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit >> dt-bindings: Add an entry for Purism SPC >> dt-bindings: arm: fsl: Add the imx8mq boards >> >> .../devicetree/bindings/arm/fsl.yaml | 7 + >> .../devicetree/bindings/vendor-prefixes.yaml | 2 + >> arch/arm64/boot/dts/freescale/Makefile | 1 + >> .../dts/freescale/imx8mq-librem5-devkit.dts | 806 >> ++++++++++++++++++ >> 4 files changed, 816 insertions(+) >> create mode 100644 >> arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts >> >> -- >> 2.17.1 >>
| |