lkml.org 
[lkml]   [2019]   [Jun]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v7 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
From
Date
Hi,

On 24/06/19 10:16 PM, Tokunori Ikegami wrote:
>
[...]
>>   +/*
>> + * Use status register to poll for Erase/write completion when DQ is not
>> + * supported. This is indicated by Bit[1:0] of SoftwareFeatures field in
>> + * CFI Primary Vendor-Specific Extended Query table 1.5
>> + */
>> +static int cfi_use_status_reg(struct cfi_private *cfi)
>> +{
>> +    struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
>> +
>> +    return extp->MinorVersion >= '5' &&
>> +        (extp->SoftwareFeatures & 0x3) == 0x1;
>
> Seems to be better to use defined values instead of 0x3 and 0x1 hard
> coded values.
>

Ok

>> +}
>> +
>> +static void cfi_check_err_status(struct map_info *map, unsigned long
>> adr)
>> +{
>> +    struct cfi_private *cfi = map->fldrv_priv;
>> +    map_word status;
>> +
>> +    if (!cfi_use_status_reg(cfi))
>> +        return;
>> +
>> +    cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
>
> Is it not necessary to set chip->start as the base parameter for
> cfi_send_gen_cmd()?
>

Right now, I am not aware of any flash that supports status registers
and are banked (that's when chip->start can be non zero). Therefore I
did not think of using chip->start.
But anyways, I will fix this up to use chip->start here and elsewhere
for next version, assuming there will be such chips in the future.

>> +             cfi->device_type, NULL);
>> +    status = map_read(map, adr);
>> +
>> +    if (map_word_bitsset(map, status, CMD(0x3a))) {
>> +        unsigned long chipstatus = MERGESTATUS(status);
>> +
>> +        if (chipstatus & CFI_SR_ESB)
>> +            pr_err("%s erase operation failed, status %lx\n",
>> +                   map->name, chipstatus);
>> +        if (chipstatus & CFI_SR_PSB)
>> +            pr_err("%s program operation failed, status %lx\n",
>> +                   map->name, chipstatus);
>> +        if (chipstatus & CFI_SR_WBASB)
>> +            pr_err("%s buffer program command aborted, status %lx\n",
>> +                   map->name, chipstatus);
>> +        if (chipstatus & CFI_SR_SLSB)
>> +            pr_err("%s sector write protected, status %lx\n",
>> +                   map->name, chipstatus);
>> +    }
>> +}
>>     /* #define DEBUG_CFI_FEATURES */
>>   @@ -744,8 +796,22 @@ static struct mtd_info *cfi_amdstd_setup(struct
>> mtd_info *mtd)
>>    */
>>   static int __xipram chip_ready(struct map_info *map, unsigned long
>> addr)
>>   {
>> +    struct cfi_private *cfi = map->fldrv_priv;
>>       map_word d, t;
>>   +    if (cfi_use_status_reg(cfi)) {
>> +        map_word ready = CMD(CFI_SR_DRB);
>> +        /*
>> +         * For chips that support status register, check device
>> +         * ready bit
>> +         */
>> +        cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
>
> Same comment as cfi_check_err_status() about the base address.
>
>> +                 cfi->device_type, NULL);
>> +        d = map_read(map, addr);
>> +
>> +        return map_word_andequal(map, d, ready, ready);
>> +    }
>> +
>>       d = map_read(map, addr);
>>       t = map_read(map, addr);
>>   @@ -769,8 +835,27 @@ static int __xipram chip_ready(struct map_info
>> *map, unsigned long addr)
>>    */
>>   static int __xipram chip_good(struct map_info *map, unsigned long
>> addr, map_word expected)
>>   {
>> +    struct cfi_private *cfi = map->fldrv_priv;
>>       map_word oldd, curd;
>>   +    if (cfi_use_status_reg(cfi)) {
>> +        map_word ready = CMD(CFI_SR_DRB);
>> +        map_word err = CMD(CFI_SR_PSB | CFI_SR_ESB);
>
> Is it not necessary to check CFI_SR_WBASB and CFI_SR_SLSB that are
> checked by cfi_check_err_status()?
>

chip_good() is used to verify whether write or erase operation really
succeeded. Looking at Cypress HyperFlash datasheets and app notes on
status register polling, its enough to see if CFI_SR_PSB or CFI_SR_PSB
is set to know if write or erase failed. Now, the reason for program or
erase failure can be known by looking at CFI_SR_WBASB and CFI_SR_SLSB
which is done for cfi_check_err_status().
Therefore, I feel, its enough to look for CFI_SR_PSB or CFI_SR_ESB here.

Thanks for the review!

Regards
Vignesh

>> +        /*
>> +         * For chips that support status register, check device
>> +         * ready bit and Erase/Program status bit to know if
>> +         * operation succeeded.
>> +         */
>> +        cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
>
> Same as cfi_check_err_status() and chip_ready() about the base address.
>
>> +                 cfi->device_type, NULL);
>> +        curd = map_read(map, addr);
>> +
>> +        if (map_word_andequal(map, curd, ready, ready))
>> +            return !map_word_bitsset(map, curd, err);
>> +
>> +        return 0;
>> +    }
>> +
>>       oldd = map_read(map, addr);
>>       curd = map_read(map, addr);
>>   @@ -1644,6 +1729,7 @@ static int __xipram do_write_oneword(struct
>> map_info *map, struct flchip *chip,
>>       /* Did we succeed? */
>>       if (!chip_good(map, adr, datum)) {
>>           /* reset on all failures. */
>> +        cfi_check_err_status(map, adr);
>>           map_write(map, CMD(0xF0), chip->start);
>>           /* FIXME - should have reset delay before continuing */
>>   @@ -1901,6 +1987,7 @@ static int __xipram do_write_buffer(struct
>> map_info *map, struct flchip *chip,
>>        * See e.g.
>>        *
>> http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf
>>
>>        */
>> +    cfi_check_err_status(map, adr);
>>       cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi,
>>                cfi->device_type, NULL);
>>       cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi,
>> @@ -2107,6 +2194,7 @@ static int do_panic_write_oneword(struct
>> map_info *map, struct flchip *chip,
>>         if (!chip_good(map, adr, datum)) {
>>           /* reset on all failures. */
>> +        cfi_check_err_status(map, adr);
>>           map_write(map, CMD(0xF0), chip->start);
>>           /* FIXME - should have reset delay before continuing */
>>   @@ -2316,6 +2404,7 @@ static int __xipram do_erase_chip(struct
>> map_info *map, struct flchip *chip)
>>       /* Did we succeed? */
>>       if (ret) {
>>           /* reset on all failures. */
>> +        cfi_check_err_status(map, adr);
>>           map_write(map, CMD(0xF0), chip->start);
>>           /* FIXME - should have reset delay before continuing */
>>   @@ -2412,6 +2501,7 @@ static int __xipram do_erase_oneblock(struct
>> map_info *map, struct flchip *chip,
>>       /* Did we succeed? */
>>       if (ret) {
>>           /* reset on all failures. */
>> +        cfi_check_err_status(map, adr);
>>           map_write(map, CMD(0xF0), chip->start);
>>           /* FIXME - should have reset delay before continuing */
>>   diff --git a/include/linux/mtd/cfi.h b/include/linux/mtd/cfi.h
>> index 208c87cf2e3e..b50416169049 100644
>> --- a/include/linux/mtd/cfi.h
>> +++ b/include/linux/mtd/cfi.h
>> @@ -219,6 +219,11 @@ struct cfi_pri_amdstd {
>>       uint8_t  VppMin;
>>       uint8_t  VppMax;
>>       uint8_t  TopBottom;
>> +    /* Below field are added from version 1.5 */
>> +    uint8_t  ProgramSuspend;
>> +    uint8_t  UnlockBypass;
>> +    uint8_t  SecureSiliconSector;
>> +    uint8_t  SoftwareFeatures;
>>   } __packed;
>>     /* Vendor-Specific PRI for Atmel chips (command set 0x0002) */

--
Regards
Vignesh

\
 
 \ /
  Last update: 2019-06-25 07:52    [W:0.059 / U:22.136 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site