lkml.org 
[lkml]   [2019]   [Jun]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 4/5] net: macb: add support for high speed interface
On Mon, Jun 24, 2019 at 01:12:35PM +0100, Parshuram Thombare wrote:
> This patch add support for high speed USXGMII PCS and 10G
> speed in Cadence ethernet controller driver.
>
> Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
> ---
> drivers/net/ethernet/cadence/macb.h | 41 +++++
> drivers/net/ethernet/cadence/macb_main.c | 189 ++++++++++++++++++++---
> 2 files changed, 207 insertions(+), 23 deletions(-)
>
> diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
> index 330da702b946..809acff19be9 100644
> --- a/drivers/net/ethernet/cadence/macb.h
> +++ b/drivers/net/ethernet/cadence/macb.h
> @@ -82,6 +82,7 @@
> #define GEM_USRIO 0x000c /* User IO */
> #define GEM_DMACFG 0x0010 /* DMA Configuration */
> #define GEM_JML 0x0048 /* Jumbo Max Length */
> +#define GEM_HS_MAC_CONFIG 0x0050 /* GEM high speed config */
> #define GEM_HRB 0x0080 /* Hash Bottom */
> #define GEM_HRT 0x0084 /* Hash Top */
> #define GEM_SA1B 0x0088 /* Specific1 Bottom */
> @@ -167,6 +168,9 @@
> #define GEM_DCFG7 0x0298 /* Design Config 7 */
> #define GEM_DCFG8 0x029C /* Design Config 8 */
> #define GEM_DCFG10 0x02A4 /* Design Config 10 */
> +#define GEM_DCFG12 0x02AC /* Design Config 12 */
> +#define GEM_USX_CONTROL 0x0A80 /* USXGMII control register */
> +#define GEM_USX_STATUS 0x0A88 /* USXGMII status register */
>
> #define GEM_TXBDCTRL 0x04cc /* TX Buffer Descriptor control register */
> #define GEM_RXBDCTRL 0x04d0 /* RX Buffer Descriptor control register */
> @@ -274,6 +278,8 @@
> #define MACB_IRXFCS_SIZE 1
>
> /* GEM specific NCR bitfields. */
> +#define GEM_ENABLE_HS_MAC_OFFSET 31
> +#define GEM_ENABLE_HS_MAC_SIZE 1
> #define GEM_TWO_PT_FIVE_GIG_OFFSET 29
> #define GEM_TWO_PT_FIVE_GIG_SIZE 1
>
> @@ -465,6 +471,10 @@
> #define MACB_REV_OFFSET 0
> #define MACB_REV_SIZE 16
>
> +/* Bitfield in HS_MAC_CONFIG */
> +#define GEM_HS_MAC_SPEED_OFFSET 0
> +#define GEM_HS_MAC_SPEED_SIZE 3
> +
> /* Bitfields in PCS_CONTROL. */
> #define GEM_PCS_CTRL_RST_OFFSET 15
> #define GEM_PCS_CTRL_RST_SIZE 1
> @@ -510,6 +520,34 @@
> #define GEM_RXBD_RDBUFF_OFFSET 8
> #define GEM_RXBD_RDBUFF_SIZE 4
>
> +/* Bitfields in DCFG12. */
> +#define GEM_HIGH_SPEED_OFFSET 26
> +#define GEM_HIGH_SPEED_SIZE 1
> +
> +/* Bitfields in USX_CONTROL. */
> +#define GEM_USX_CTRL_SPEED_OFFSET 14
> +#define GEM_USX_CTRL_SPEED_SIZE 3
> +#define GEM_SERDES_RATE_OFFSET 12
> +#define GEM_SERDES_RATE_SIZE 2
> +#define GEM_RX_SCR_BYPASS_OFFSET 9
> +#define GEM_RX_SCR_BYPASS_SIZE 1
> +#define GEM_TX_SCR_BYPASS_OFFSET 8
> +#define GEM_TX_SCR_BYPASS_SIZE 1
> +#define GEM_RX_SYNC_RESET_OFFSET 2
> +#define GEM_RX_SYNC_RESET_SIZE 1
> +#define GEM_TX_EN_OFFSET 1
> +#define GEM_TX_EN_SIZE 1
> +#define GEM_SIGNAL_OK_OFFSET 0
> +#define GEM_SIGNAL_OK_SIZE 1
> +
> +/* Bitfields in USX_STATUS. */
> +#define GEM_USX_TX_FAULT_OFFSET 28
> +#define GEM_USX_TX_FAULT_SIZE 1
> +#define GEM_USX_RX_FAULT_OFFSET 27
> +#define GEM_USX_RX_FAULT_SIZE 1
> +#define GEM_USX_BLOCK_LOCK_OFFSET 0
> +#define GEM_USX_BLOCK_LOCK_SIZE 1
> +
> /* Bitfields in TISUBN */
> #define GEM_SUBNSINCR_OFFSET 0
> #define GEM_SUBNSINCR_SIZE 16
> @@ -670,6 +708,7 @@
> #define MACB_CAPS_MACB_IS_GEM BIT(31)
> #define MACB_CAPS_PCS BIT(24)
> #define MACB_CAPS_MACB_IS_GEM_GXL BIT(25)
> +#define MACB_CAPS_HIGH_SPEED BIT(26)
>
> #define MACB_GEM7010_IDNUM 0x009
> #define MACB_GEM7014_IDNU 0x107
> @@ -749,6 +788,7 @@
> })
>
> #define MACB_READ_NSR(bp) macb_readl(bp, NSR)
> +#define GEM_READ_USX_STATUS(bp) gem_readl(bp, USX_STATUS)
>
> /* struct macb_dma_desc - Hardware DMA descriptor
> * @addr: DMA address of data buffer
> @@ -1262,6 +1302,7 @@ struct macb {
> struct macb_pm_data pm_data;
> struct phylink *pl;
> struct phylink_config pl_config;
> + u32 serdes_rate;
> };
>
> #ifdef CONFIG_MACB_USE_HWSTAMP
> diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
> index 1323f9b4d3b8..5afc03299bee 100644
> --- a/drivers/net/ethernet/cadence/macb_main.c
> +++ b/drivers/net/ethernet/cadence/macb_main.c
> @@ -84,6 +84,20 @@ static struct sifive_fu540_macb_mgmt *mgmt;
> #define MACB_WOL_HAS_MAGIC_PACKET (0x1 << 0)
> #define MACB_WOL_ENABLED (0x1 << 1)
>
> +enum {
> + HS_MAC_SPEED_100M,
> + HS_MAC_SPEED_1000M,
> + HS_MAC_SPEED_2500M,
> + HS_MAC_SPEED_5000M,
> + HS_MAC_SPEED_10000M,
> + HS_MAC_SPEED_25000M,
> +};
> +
> +enum {
> + MACB_SERDES_RATE_5Gbps = 5,
> + MACB_SERDES_RATE_10Gbps = 10,
> +};
> +
> /* Graceful stop timeouts in us. We should allow up to
> * 1 frame time (10 Mbits/s, full-duplex, ignoring collisions)
> */
> @@ -93,6 +107,8 @@ static struct sifive_fu540_macb_mgmt *mgmt;
>
> #define MACB_MDIO_TIMEOUT 1000000 /* in usecs */
>
> +#define MACB_USX_BLOCK_LOCK_TIMEOUT 1000000 /* in usecs */
> +
> /* DMA buffer descriptor might be different size
> * depends on hardware configuration:
> *
> @@ -439,23 +455,37 @@ static int macb_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
> */
> static void macb_set_tx_clk(struct clk *clk, int speed, struct net_device *dev)
> {
> + struct macb *bp = netdev_priv(dev);
> long ferr, rate, rate_rounded;
>
> if (!clk)
> return;
>
> - switch (speed) {
> - case SPEED_10:
> - rate = 2500000;
> - break;
> - case SPEED_100:
> - rate = 25000000;
> - break;
> - case SPEED_1000:
> - rate = 125000000;
> - break;
> - default:
> - return;
> + if (bp->phy_interface == PHY_INTERFACE_MODE_USXGMII) {
> + switch (bp->serdes_rate) {
> + case MACB_SERDES_RATE_5Gbps:
> + rate = 78125000;
> + break;
> + case MACB_SERDES_RATE_10Gbps:
> + rate = 156250000;
> + break;
> + default:
> + return;
> + }
> + } else {
> + switch (speed) {
> + case SPEED_10:
> + rate = 2500000;
> + break;
> + case SPEED_100:
> + rate = 25000000;
> + break;
> + case SPEED_1000:
> + rate = 125000000;
> + break;
> + default:
> + return;
> + }
> }
>
> rate_rounded = clk_round_rate(clk, rate);
> @@ -485,6 +515,21 @@ static void gem_phylink_validate(struct phylink_config *pl_config,
>
> switch (state->interface) {
> case PHY_INTERFACE_MODE_NA:
> + case PHY_INTERFACE_MODE_USXGMII:
> + case PHY_INTERFACE_MODE_10GKR:
> + if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE) {
> + phylink_set(mask, 10000baseCR_Full);
> + phylink_set(mask, 10000baseER_Full);
> + phylink_set(mask, 10000baseKR_Full);
> + phylink_set(mask, 10000baseLR_Full);
> + phylink_set(mask, 10000baseLRM_Full);
> + phylink_set(mask, 10000baseSR_Full);
> + phylink_set(mask, 10000baseT_Full);
> + phylink_set(mask, 5000baseT_Full);
> + phylink_set(mask, 2500baseX_Full);
> + phylink_set(mask, 1000baseX_Full);
> + }

If MACB_CAPS_GIGABIT_MODE_AVAILABLE is not set, are these interface
modes supported by the hardware? If the PHY interface mode is not
supported, then the returned support mask must be cleared.

> + /* fallthrough */
> case PHY_INTERFACE_MODE_SGMII:
> case PHY_INTERFACE_MODE_GMII:
> case PHY_INTERFACE_MODE_RGMII:
> @@ -516,6 +561,91 @@ static int gem_phylink_mac_link_state(struct phylink_config *pl_config,
> return -EOPNOTSUPP;
> }
>
> +static int macb_wait_for_usx_block_lock(struct macb *bp)
> +{
> + u32 val;
> +
> + return readx_poll_timeout(GEM_READ_USX_STATUS, bp, val,
> + val & GEM_BIT(USX_BLOCK_LOCK),
> + 1, MACB_USX_BLOCK_LOCK_TIMEOUT);
> +}
> +
> +static inline int gem_mac_usx_configure(struct macb *bp, int spd)
> +{
> + u32 speed, config;
> +
> + gem_writel(bp, NCFGR, GEM_BIT(PCSSEL) |
> + (~GEM_BIT(SGMIIEN) & gem_readl(bp, NCFGR)));
> + gem_writel(bp, NCR, gem_readl(bp, NCR) |
> + GEM_BIT(ENABLE_HS_MAC));
> + gem_writel(bp, NCFGR, gem_readl(bp, NCFGR) |
> + MACB_BIT(FD));
> + config = gem_readl(bp, USX_CONTROL);
> + config = GEM_BFINS(SERDES_RATE, bp->serdes_rate, config);
> + config &= ~GEM_BIT(TX_SCR_BYPASS);
> + config &= ~GEM_BIT(RX_SCR_BYPASS);
> + gem_writel(bp, USX_CONTROL, config |
> + GEM_BIT(TX_EN));
> + config = gem_readl(bp, USX_CONTROL);
> + gem_writel(bp, USX_CONTROL, config | GEM_BIT(SIGNAL_OK));
> + if (macb_wait_for_usx_block_lock(bp) < 0) {
> + netdev_warn(bp->dev, "USXGMII block lock failed");
> + return -ETIMEDOUT;
> + }
> +
> + switch (spd) {
> + case SPEED_10000:
> + if (bp->serdes_rate >= MACB_SERDES_RATE_10Gbps) {
> + speed = HS_MAC_SPEED_10000M;
> + } else {
> + netdev_warn(bp->dev, "10G speed isn't supported by HW");
> + netdev_warn(bp->dev, "Setting speed to 1G");
> + speed = HS_MAC_SPEED_1000M;
> + }
> + break;
> + case SPEED_5000:
> + speed = HS_MAC_SPEED_5000M;
> + break;
> + case SPEED_2500:
> + speed = HS_MAC_SPEED_2500M;
> + break;
> + case SPEED_1000:
> + speed = HS_MAC_SPEED_1000M;
> + break;
> + default:
> + case SPEED_100:
> + speed = HS_MAC_SPEED_100M;
> + break;
> + }
> +
> + gem_writel(bp, HS_MAC_CONFIG, GEM_BFINS(HS_MAC_SPEED, speed,
> + gem_readl(bp, HS_MAC_CONFIG)));
> + gem_writel(bp, USX_CONTROL, GEM_BFINS(USX_CTRL_SPEED, speed,
> + gem_readl(bp, USX_CONTROL)));
> + return 0;
> +}
> +
> +static inline void gem_mac_configure(struct macb *bp, int speed)
> +{
> + if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII)
> + gem_writel(bp, NCFGR, GEM_BIT(SGMIIEN) |
> + GEM_BIT(PCSSEL) |
> + gem_readl(bp, NCFGR));

Is this still necessary?

> +
> + switch (speed) {
> + case SPEED_1000:
> + gem_writel(bp, NCFGR, GEM_BIT(GBE) |
> + gem_readl(bp, NCFGR));
> + break;
> + case SPEED_100:
> + macb_writel(bp, NCFGR, MACB_BIT(SPD) |
> + macb_readl(bp, NCFGR));

What happens to the NCFGR register if we call mac_config() first for
a 1G speed, then 100M and finally 10M - what value does the NCFGR
register end up with?

I suspect it ends up with both the GBE and SPD bits set, and that is
probably not what you want.

> + break;
> + default:
> + break;
> + }
> +}
> +
> static void gem_mac_config(struct phylink_config *pl_config, unsigned int mode,
> const struct phylink_link_state *state)
> {
> @@ -558,18 +688,17 @@ static void gem_mac_config(struct phylink_config *pl_config, unsigned int mode,
>
> if (state->duplex)
> reg |= MACB_BIT(FD);
> + macb_or_gem_writel(bp, NCFGR, reg);
>
> - switch (state->speed) {
> - case SPEED_1000:
> - reg |= GEM_BIT(GBE);
> - break;
> - case SPEED_100:
> - reg |= MACB_BIT(SPD);
> - break;
> - default:
> - break;
> + if (bp->phy_interface == PHY_INTERFACE_MODE_USXGMII) {
> + if (gem_mac_usx_configure(bp, state->speed) < 0) {
> + spin_unlock_irqrestore(&bp->lock, flags);
> + phylink_mac_change(bp->pl, false);
> + return;
> + }
> + } else {
> + gem_mac_configure(bp, state->speed);
> }
> - macb_or_gem_writel(bp, NCFGR, reg);
>
> bp->speed = state->speed;
> bp->duplex = state->duplex;
> @@ -3416,6 +3545,9 @@ static void macb_configure_caps(struct macb *bp,
> default:
> break;
> }
> + dcfg = gem_readl(bp, DCFG12);
> + if (GEM_BFEXT(HIGH_SPEED, dcfg) == 1)
> + bp->caps |= MACB_CAPS_HIGH_SPEED;
> dcfg = gem_readl(bp, DCFG2);
> if ((dcfg & (GEM_BIT(RX_PKT_BUFF) | GEM_BIT(TX_PKT_BUFF))) == 0)
> bp->caps |= MACB_CAPS_FIFO_MODE;
> @@ -4404,7 +4536,18 @@ static int macb_probe(struct platform_device *pdev)
> } else if (bp->caps & MACB_CAPS_MACB_IS_GEM_GXL) {
> u32 interface_supported = 1;
>
> - if (phy_mode == PHY_INTERFACE_MODE_SGMII) {
> + if (phy_mode == PHY_INTERFACE_MODE_USXGMII) {
> + if (!(bp->caps & MACB_CAPS_HIGH_SPEED &&
> + bp->caps & MACB_CAPS_PCS))
> + interface_supported = 0;
> +
> + if (of_property_read_u32(np, "serdes-rate-gbps",
> + &bp->serdes_rate)) {
> + netdev_err(dev,
> + "GEM serdes_rate not specified");
> + interface_supported = 0;
> + }
> + } else if (phy_mode == PHY_INTERFACE_MODE_SGMII) {
> if (!(bp->caps & MACB_CAPS_PCS))
> interface_supported = 0;
> } else if (phy_mode == PHY_INTERFACE_MODE_GMII ||
> --
> 2.17.1
>
>

--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up

\
 
 \ /
  Last update: 2019-06-24 15:49    [W:0.119 / U:46.104 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site