lkml.org 
[lkml]   [2019]   [Jun]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] drivers/staging/rtl8192u: adjust block comments
Date
The coding-styles.rst states, that multiline comments should
allways contain a leading "*" in each line.
For multiline comments in general they

/*
* should look
* like this.
*/

For multiline comments in either net/ or drivers/net/ however,
they should

/* omit
* the first
* empty line.
*/

Since this file is part of a networking driver, the goal for it would
be to reside in drivers/net/ one day.

This patch changes comments, that were in neither form of the two listed
above, to have the style that is specified for drivers/net/.

Signed-off-by: Christian Müller <muellerch-privat@web.de>
Signed-off-by: Felix Trommer <felix.trommer@hotmail.de>
---
drivers/staging/rtl8192u/r8192U_dm.c | 28 ++++++++++++++++------------
1 file changed, 16 insertions(+), 12 deletions(-)

diff --git a/drivers/staging/rtl8192u/r8192U_dm.c b/drivers/staging/rtl8192u/r8192U_dm.c
index 86215fee8f0b..cb6c653e624d 100644
--- a/drivers/staging/rtl8192u/r8192U_dm.c
+++ b/drivers/staging/rtl8192u/r8192U_dm.c
@@ -332,9 +332,10 @@ static void dm_check_rate_adaptive(struct net_device *dev)
((bshort_gi_enabled) ? BIT(31) : 0);

/* 2007/10/08 MH We support RA smooth scheme now. When it is the first
- time to link with AP. We will not change upper/lower threshold. If
- STA stay in high or low level, we must change two different threshold
- to prevent jumping frequently. */
+ * time to link with AP. We will not change upper/lower threshold. If
+ * STA stay in high or low level, we must change two different threshold
+ * to prevent jumping frequently.
+ */
if (pra->ratr_state == DM_RATR_STA_HIGH) {
HighRSSIThreshForRA = pra->high2low_rssi_thresh_for_ra;
LowRSSIThreshForRA = (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20) ?
@@ -1738,10 +1739,12 @@ static void dm_ctrl_initgain_byrssi_by_fwfalse_alarm(
pHalData->UndecoratedSmoothedPWDB, DM_DigTable.RssiLowThresh,
DM_DigTable.RssiHighThresh, DM_DigTable.Dig_State);*/
/* 1. When RSSI decrease, We have to judge if it is smaller than a threshold
- and then execute the step below. */
+ * and then execute the step below.
+ */
if (priv->undecorated_smoothed_pwdb <= dm_digtable.rssi_low_thresh) {
/* 2008/02/05 MH When we execute silent reset, the DIG PHY parameters
- will be reset to init value. We must prevent the condition. */
+ * will be reset to init value. We must prevent the condition.
+ */
if (dm_digtable.dig_state == DM_STA_DIG_OFF &&
(priv->reset_count == reset_cnt)) {
return;
@@ -1786,7 +1789,8 @@ static void dm_ctrl_initgain_byrssi_by_fwfalse_alarm(
}

/* 2. When RSSI increase, We have to judge if it is larger than a threshold
- and then execute the step below. */
+ * and then execute the step below.
+ */
if (priv->undecorated_smoothed_pwdb >= dm_digtable.rssi_high_thresh) {
u8 reset_flag = 0;

@@ -2252,11 +2256,10 @@ static void dm_ctstoself(struct net_device *dev)
pHTInfo->IOTAction &= ~HT_IOT_ACT_FORCED_CTS2SELF;
return;
}
- /*
- 1. Uplink
- 2. Linksys350/Linksys300N
- 3. <50 disable, >55 enable
- */
+ /* 1. Uplink
+ * 2. Linksys350/Linksys300N
+ * 3. <50 disable, >55 enable
+ */

if (pHTInfo->IOTPeer == HT_IOT_PEER_BROADCOM) {
curTxOkCnt = priv->stats.txbytesunicast - lastTxOkCnt;
@@ -2333,7 +2336,8 @@ void dm_rf_pathcheck_workitemcallback(struct work_struct *work)
u8 rfpath = 0, i;

/* 2008/01/30 MH After discussing with SD3 Jerry, 0xc04/0xd04 register will
- always be the same. We only read 0xc04 now. */
+ * always be the same. We only read 0xc04 now.
+ */
read_nic_byte(dev, 0xc04, &rfpath);

/* Check Bit 0-3, it means if RF A-D is enabled. */
--
2.17.1
\
 
 \ /
  Last update: 2019-06-24 11:47    [W:0.086 / U:10.892 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site