lkml.org 
[lkml]   [2019]   [Jun]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 3/4] ARM: dts: exynos: Add regulator suspend configuration to Odroid XU3/XU4/HC1 family
From
Date
Hi Krzysztof,

On 2019-06-24 09:41, Krzysztof Kozlowski wrote:
> On Mon, 24 Jun 2019 at 09:20, Marek Szyprowski <m.szyprowski@samsung.com> wrote:
>> On 2019-06-23 18:02, Anand Moon wrote:
>>> Thanks for this patch. Please add my
>>>
>>> Tested-by: Anand Moon <linux.amoon@gmail.com>
>>>
>>> [snip]
>>>
>>> Could you integrate below small changes into this patch.
>>> with these below changes suspend and resume work correctly at my end.
>>>
>>> [1] XU4_suspendresume.patch
>>>
>>> As per S2MPS11B PMIC 1.2.1 Regulator (Features)
>>> Fix the min max value for *Buck7* and *Buck8*
>>>
>>> -- Buck7 (VDD_1.0V_LDO) 1.5 A (1.2 V to 1.5 V, 12.5 mV step, default on 1.35 V)
>>> -- Buck8 (VDD_1.8V_LDO) 2.5 A (1.8 V to 2.1 V, 12.5 mV step, default on 2.0 V)
>> Could you elaborate why such change for Buck7 and Buck8 is needed?
> Anand has here valid point - the constraints in DTS do not match
> hardware manual. This leads to question whether voltage table in
> driver is proper... Another point is the voltage itself. The
> schematics describes them as at specific voltage (1.35 V and 2.0 V)
> but after boot they are 1.2 V and 1.85 V. Maybe this shift comes from
> the problem above.
>
>>> Also add suspend-off for *Buck9*
>>> Buck9 internally controls the power of USB hub.
>>> Adding suspend the this node help proper reset of USB hub on Odroid
>>> XU4 / HC1/ XU3
>>> during suspend and resume. Below it the logs from my testing.
>> Disabling Buck9 in suspend indeed reduces the power consumed by the
>> board during suspend-to-ram from about 80mA to as little as 7-10mA, what
>> matches the results of OdroidXU3. Thanks for the hint!
> Although I did not get what is the difference in the logs (Anand
> pasted two logs but they look the same) but the power consumption is
> reason is good enough. I would be happy to put in the changelog entire
> consumption difference. I can measure it on XU3-Lite but can you give
> me the XU4 (before and after)?\


HC1:

next-20190620: 120mA (@5V)
this patchset: 72mA (@5V)
this patchset + fixup from Anand: 7-10mA (@5V)

XU4 (SDcard):

next-20190620: 88mA (@5V)
this patchset: 74mA (@5V), sometimes 42mA (@5V)
this patchset + fixup from Anand: 6-9mA (@5V)


XU4 (eMMC):

next-20190620: 100mA (@5V)
this patchset: 72mA (@5V), sometimes 41mA (@5V)
this patchset + fixup from Anand: 6-9mA (@5V)


Best regards
--
Marek Szyprowski, PhD
Samsung R&D Institute Poland

\
 
 \ /
  Last update: 2019-06-24 11:02    [W:0.104 / U:26.632 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site