lkml.org 
[lkml]   [2019]   [Jun]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH V10 11/15] arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT
From
Date
On 6/20/2019 4:25 PM, Thierry Reding wrote:
> On Wed, Jun 12, 2019 at 03:23:35PM +0530, Vidya Sagar wrote:
>> Add P2U (PIPE to UPHY) and PCIe controller nodes to device tree.
>> The Tegra194 SoC contains six PCIe controllers and twenty P2U instances
>> grouped into two different PHY bricks namely High-Speed IO (HSIO-12 P2Us)
>> and NVIDIA High Speed (NVHS-8 P2Us) respectively.
>>
>> Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
>> ---
>> Changes since [v9]:
>> * None
>>
>> Changes since [v8]:
>> * None
>>
>> Changes since [v7]:
>> * Replaced 'core_apb' with 'apb' in reset names
>> * Used macros instead of hardcoded numbers in 'interrupt-map' property
>> * Aligned 'ranges' entries
>>
>> Changes since [v6]:
>> * Removed properties "nvidia,disable-aspm-states" & "nvidia,controller-id".
>> * Modified property "nvidia,bpmp" to include controller-id as well.
>>
>> Changes since [v5]:
>> * Changes 'p2u@xxxxxxxx' to 'phy@xxxxxxxx'
>> * Arranged all PCIe nodes in the order of their addresses
>>
>> Changes since [v4]:
>> * None
>>
>> Changes since [v3]:
>> * None
>>
>> Changes since [v2]:
>> * Included 'hsio' or 'nvhs' in P2U node's label names to reflect which brick
>> they belong to
>> * Removed leading zeros in unit address
>>
>> Changes since [v1]:
>> * Flattened all P2U nodes by removing 'hsio-p2u' and 'nvhs-p2u' super nodes
>> * Changed P2U nodes compatible string from 'nvidia,tegra194-phy-p2u' to 'nvidia,tegra194-p2u'
>> * Changed reg-name from 'base' to 'ctl'
>> * Updated all PCIe nodes according to the changes made to DT documentation file
>>
>> arch/arm64/boot/dts/nvidia/tegra194.dtsi | 437 +++++++++++++++++++++++
>> 1 file changed, 437 insertions(+)
>
> Applied to for-5.3/arm64/dt, thanks.
>
> I did end up sorting the new nodes differently so that they are ordered
> according to the general rules (sort by unit-address, then
> alphabetically). That's slightly complicated by the fact that the PCI
> controllers have registers that seem to be right in the middle of the
> host1x aperture, so I had to bend the rules a little.
>
> Thierry

I see that you moved all PCIe nodes under CBB node. There is an issue with that.
PCIe nodes have apertures defined in both 32-bit region and 64-bit region which
are mentioned through "ranges" property. Apertures defined in 64-bit region do not
fit within "ranges" defined for CBB region which can handle only 32-bit "ranges" of
CBB sub-nodes and ends @ 0x40000000. It is because of this reason that I kept PCIe
nodes outside of CBB master node. Do you agree with my understanding? If yes, can
you please move PCIe nodes out of CBB node? (Also in platform dts file)

Thanks,
Vidya Sagar

>
>> diff --git a/arch/arm64/boot/dts/nvidia/tegra194.dtsi b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
>> index c77ca211fa8f..feba034f26f0 100644
>> --- a/arch/arm64/boot/dts/nvidia/tegra194.dtsi
>> +++ b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
>> @@ -884,6 +884,166 @@
>> nvidia,interface = <3>;
>> };
>> };
>> +
>> + p2u_hsio_0: phy@3e10000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e10000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_1: phy@3e20000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e20000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_2: phy@3e30000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e30000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_3: phy@3e40000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e40000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_4: phy@3e50000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e50000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_5: phy@3e60000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e60000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_6: phy@3e70000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e70000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_7: phy@3e80000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e80000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_8: phy@3e90000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03e90000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_9: phy@3ea0000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03ea0000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_nvhs_0: phy@3eb0000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03eb0000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_nvhs_1: phy@3ec0000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03ec0000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_nvhs_2: phy@3ed0000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03ed0000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_nvhs_3: phy@3ee0000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03ee0000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_nvhs_4: phy@3ef0000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03ef0000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_nvhs_5: phy@3f00000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03f00000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_nvhs_6: phy@3f10000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03f10000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_nvhs_7: phy@3f20000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03f20000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_10: phy@3f30000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03f30000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> +
>> + p2u_hsio_11: phy@3f40000 {
>> + compatible = "nvidia,tegra194-p2u";
>> + reg = <0x03f40000 0x10000>;
>> + reg-names = "ctl";
>> +
>> + #phy-cells = <0>;
>> + };
>> };
>>
>> sysram@40000000 {
>> @@ -1054,4 +1214,281 @@
>> (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
>> interrupt-parent = <&gic>;
>> };
>> +
>> + pcie@14100000 {
>> + compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
>> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX1A>;
>> + reg = <0x00 0x14100000 0x0 0x00020000 /* appl registers (128K) */
>> + 0x00 0x30000000 0x0 0x00040000 /* configuration space (256K) */
>> + 0x00 0x30040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */
>> + 0x00 0x30080000 0x0 0x00040000>; /* DBI reg space (256K) */
>> + reg-names = "appl", "config", "atu_dma", "dbi";
>> +
>> + status = "disabled";
>> +
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + device_type = "pci";
>> + num-lanes = <1>;
>> + num-viewport = <8>;
>> + linux,pci-domain = <1>;
>> +
>> + clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_1>;
>> + clock-names = "core";
>> +
>> + resets = <&bpmp TEGRA194_RESET_PEX0_CORE_1_APB>,
>> + <&bpmp TEGRA194_RESET_PEX0_CORE_1>;
>> + reset-names = "apb", "core";
>> +
>> + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
>> + <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
>> + interrupt-names = "intr", "msi";
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0>;
>> + interrupt-map = <0 0 0 0 &gic GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + nvidia,bpmp = <&bpmp 1>;
>> +
>> + supports-clkreq;
>> + nvidia,aspm-cmrt-us = <60>;
>> + nvidia,aspm-pwr-on-t-us = <20>;
>> + nvidia,aspm-l0s-entrance-latency-us = <3>;
>> +
>> + bus-range = <0x0 0xff>;
>> + ranges = <0x81000000 0x0 0x30100000 0x0 0x30100000 0x0 0x00100000 /* downstream I/O (1MB) */
>> + 0xc2000000 0x12 0x00000000 0x12 0x00000000 0x0 0x30000000 /* prefetchable memory (768MB) */
>> + 0x82000000 0x0 0x40000000 0x12 0x30000000 0x0 0x10000000>; /* non-prefetchable memory (256MB) */
>> + };
>> +
>> + pcie@14120000 {
>> + compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
>> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX1A>;
>> + reg = <0x00 0x14120000 0x0 0x00020000 /* appl registers (128K) */
>> + 0x00 0x32000000 0x0 0x00040000 /* configuration space (256K) */
>> + 0x00 0x32040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */
>> + 0x00 0x32080000 0x0 0x00040000>; /* DBI reg space (256K) */
>> + reg-names = "appl", "config", "atu_dma", "dbi";
>> +
>> + status = "disabled";
>> +
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + device_type = "pci";
>> + num-lanes = <1>;
>> + num-viewport = <8>;
>> + linux,pci-domain = <2>;
>> +
>> + clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_2>;
>> + clock-names = "core";
>> +
>> + resets = <&bpmp TEGRA194_RESET_PEX0_CORE_2_APB>,
>> + <&bpmp TEGRA194_RESET_PEX0_CORE_2>;
>> + reset-names = "apb", "core";
>> +
>> + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
>> + <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
>> + interrupt-names = "intr", "msi";
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0>;
>> + interrupt-map = <0 0 0 0 &gic GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + nvidia,bpmp = <&bpmp 2>;
>> +
>> + supports-clkreq;
>> + nvidia,aspm-cmrt-us = <60>;
>> + nvidia,aspm-pwr-on-t-us = <20>;
>> + nvidia,aspm-l0s-entrance-latency-us = <3>;
>> +
>> + bus-range = <0x0 0xff>;
>> + ranges = <0x81000000 0x0 0x32100000 0x0 0x32100000 0x0 0x00100000 /* downstream I/O (1MB) */
>> + 0xc2000000 0x12 0x40000000 0x12 0x40000000 0x0 0x30000000 /* prefetchable memory (768MB) */
>> + 0x82000000 0x0 0x40000000 0x12 0x70000000 0x0 0x10000000>; /* non-prefetchable memory (256MB) */
>> + };
>> +
>> + pcie@14140000 {
>> + compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
>> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX1A>;
>> + reg = <0x00 0x14140000 0x0 0x00020000 /* appl registers (128K) */
>> + 0x00 0x34000000 0x0 0x00040000 /* configuration space (256K) */
>> + 0x00 0x34040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */
>> + 0x00 0x34080000 0x0 0x00040000>; /* DBI reg space (256K) */
>> + reg-names = "appl", "config", "atu_dma", "dbi";
>> +
>> + status = "disabled";
>> +
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + device_type = "pci";
>> + num-lanes = <1>;
>> + num-viewport = <8>;
>> + linux,pci-domain = <3>;
>> +
>> + clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_3>;
>> + clock-names = "core";
>> +
>> + resets = <&bpmp TEGRA194_RESET_PEX0_CORE_3_APB>,
>> + <&bpmp TEGRA194_RESET_PEX0_CORE_3>;
>> + reset-names = "apb", "core";
>> +
>> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
>> + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
>> + interrupt-names = "intr", "msi";
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0>;
>> + interrupt-map = <0 0 0 0 &gic GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + nvidia,bpmp = <&bpmp 3>;
>> +
>> + supports-clkreq;
>> + nvidia,aspm-cmrt-us = <60>;
>> + nvidia,aspm-pwr-on-t-us = <20>;
>> + nvidia,aspm-l0s-entrance-latency-us = <3>;
>> +
>> + bus-range = <0x0 0xff>;
>> + ranges = <0x81000000 0x0 0x34100000 0x0 0x34100000 0x0 0x00100000 /* downstream I/O (1MB) */
>> + 0xc2000000 0x12 0x80000000 0x12 0x80000000 0x0 0x30000000 /* prefetchable memory (768MB) */
>> + 0x82000000 0x0 0x40000000 0x12 0xb0000000 0x0 0x10000000>; /* non-prefetchable memory (256MB) */
>> + };
>> +
>> + pcie@14160000 {
>> + compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
>> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX4A>;
>> + reg = <0x00 0x14160000 0x0 0x00020000 /* appl registers (128K) */
>> + 0x00 0x36000000 0x0 0x00040000 /* configuration space (256K) */
>> + 0x00 0x36040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */
>> + 0x00 0x36080000 0x0 0x00040000>; /* DBI reg space (256K) */
>> + reg-names = "appl", "config", "atu_dma", "dbi";
>> +
>> + status = "disabled";
>> +
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + device_type = "pci";
>> + num-lanes = <4>;
>> + num-viewport = <8>;
>> + linux,pci-domain = <4>;
>> +
>> + clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_4>;
>> + clock-names = "core";
>> +
>> + resets = <&bpmp TEGRA194_RESET_PEX0_CORE_4_APB>,
>> + <&bpmp TEGRA194_RESET_PEX0_CORE_4>;
>> + reset-names = "apb", "core";
>> +
>> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
>> + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
>> + interrupt-names = "intr", "msi";
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0>;
>> + interrupt-map = <0 0 0 0 &gic GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + nvidia,bpmp = <&bpmp 4>;
>> +
>> + supports-clkreq;
>> + nvidia,aspm-cmrt-us = <60>;
>> + nvidia,aspm-pwr-on-t-us = <20>;
>> + nvidia,aspm-l0s-entrance-latency-us = <3>;
>> +
>> + bus-range = <0x0 0xff>;
>> + ranges = <0x81000000 0x0 0x36100000 0x0 0x36100000 0x0 0x00100000 /* downstream I/O (1MB) */
>> + 0xc2000000 0x14 0x00000000 0x14 0x00000000 0x3 0x40000000 /* prefetchable memory (13GB) */
>> + 0x82000000 0x0 0x40000000 0x17 0x40000000 0x0 0xc0000000>; /* non-prefetchable memory (3GB) */
>> + };
>> +
>> + pcie@14180000 {
>> + compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
>> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>;
>> + reg = <0x00 0x14180000 0x0 0x00020000 /* appl registers (128K) */
>> + 0x00 0x38000000 0x0 0x00040000 /* configuration space (256K) */
>> + 0x00 0x38040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */
>> + 0x00 0x38080000 0x0 0x00040000>; /* DBI reg space (256K) */
>> + reg-names = "appl", "config", "atu_dma", "dbi";
>> +
>> + status = "disabled";
>> +
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + device_type = "pci";
>> + num-lanes = <8>;
>> + num-viewport = <8>;
>> + linux,pci-domain = <0>;
>> +
>> + clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>;
>> + clock-names = "core";
>> +
>> + resets = <&bpmp TEGRA194_RESET_PEX0_CORE_0_APB>,
>> + <&bpmp TEGRA194_RESET_PEX0_CORE_0>;
>> + reset-names = "apb", "core";
>> +
>> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
>> + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
>> + interrupt-names = "intr", "msi";
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0>;
>> + interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + nvidia,bpmp = <&bpmp 0>;
>> +
>> + supports-clkreq;
>> + nvidia,aspm-cmrt-us = <60>;
>> + nvidia,aspm-pwr-on-t-us = <20>;
>> + nvidia,aspm-l0s-entrance-latency-us = <3>;
>> +
>> + bus-range = <0x0 0xff>;
>> + ranges = <0x81000000 0x0 0x38100000 0x0 0x38100000 0x0 0x00100000 /* downstream I/O (1MB) */
>> + 0xc2000000 0x18 0x00000000 0x18 0x00000000 0x3 0x40000000 /* prefetchable memory (13GB) */
>> + 0x82000000 0x0 0x40000000 0x1b 0x40000000 0x0 0xc0000000>; /* non-prefetchable memory (3GB) */
>> + };
>> +
>> + pcie@141a0000 {
>> + compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
>> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>;
>> + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */
>> + 0x00 0x3a000000 0x0 0x00040000 /* configuration space (256K) */
>> + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */
>> + 0x00 0x3a080000 0x0 0x00040000>; /* DBI reg space (256K) */
>> + reg-names = "appl", "config", "atu_dma", "dbi";
>> +
>> + status = "disabled";
>> +
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + device_type = "pci";
>> + num-lanes = <8>;
>> + num-viewport = <8>;
>> + linux,pci-domain = <5>;
>> +
>> + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>,
>> + <&bpmp TEGRA194_CLK_PEX1_CORE_5M>;
>> + clock-names = "core", "core_m";
>> +
>> + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>,
>> + <&bpmp TEGRA194_RESET_PEX1_CORE_5>;
>> + reset-names = "apb", "core";
>> +
>> + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
>> + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
>> + interrupt-names = "intr", "msi";
>> +
>> + nvidia,bpmp = <&bpmp 5>;
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0>;
>> + interrupt-map = <0 0 0 0 &gic GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + supports-clkreq;
>> + nvidia,aspm-cmrt-us = <60>;
>> + nvidia,aspm-pwr-on-t-us = <20>;
>> + nvidia,aspm-l0s-entrance-latency-us = <3>;
>> +
>> + bus-range = <0x0 0xff>;
>> + ranges = <0x81000000 0x0 0x3a100000 0x0 0x3a100000 0x0 0x00100000 /* downstream I/O (1MB) */
>> + 0xc2000000 0x1c 0x00000000 0x1c 0x00000000 0x3 0x40000000 /* prefetchable memory (13GB) */
>> + 0x82000000 0x0 0x40000000 0x1f 0x40000000 0x0 0xc0000000>; /* non-prefetchable memory (3GB) */
>> + };
>> };
>> --
>> 2.17.1
>>

\
 
 \ /
  Last update: 2019-06-24 09:33    [W:0.069 / U:0.140 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site