lkml.org 
[lkml]   [2019]   [Jun]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 2/2] ARM: dts: Add support for 96Boards Meerkat96 board
On Fri, Jun 14, 2019 at 05:14:33PM +0530, Manivannan Sadhasivam wrote:
> Hi Shawn,
>
> On Thu, Jun 13, 2019 at 06:57:05PM +0530, Manivannan Sadhasivam wrote:
> > Add devicetree support for 96Boards Meerkat96 board from Novtech. This
> > board is one of the Consumer Edition boards of the 96Boards family based
> > on i.MX7D SoC. Following are the currently supported features of the
> > board:
> >
> > * uSD
> > * WiFi/BT
> > * USB
> >
> > More information about this board can be found in 96Boards product page:
> > https://www.96boards.org/product/imx7-96/
> >
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > ---
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/imx7d-meerkat96.dts | 389 ++++++++++++++++++++++++++
> > 2 files changed, 390 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx7d-meerkat96.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index f4f5aeaf3298..3018a763dbd1 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -579,6 +579,7 @@ dtb-$(CONFIG_SOC_IMX7D) += \
> > imx7d-cl-som-imx7.dtb \
> > imx7d-colibri-emmc-eval-v3.dtb \
> > imx7d-colibri-eval-v3.dtb \
> > + imx7d-meerkat96.dtb \
> > imx7d-nitrogen7.dtb \
> > imx7d-pico-hobbit.dtb \
> > imx7d-pico-pi.dtb \
> > diff --git a/arch/arm/boot/dts/imx7d-meerkat96.dts b/arch/arm/boot/dts/imx7d-meerkat96.dts
> > new file mode 100644
> > index 000000000000..a86dc4878e44
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx7d-meerkat96.dts
> > @@ -0,0 +1,389 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR MIT
> > +/*
> > + * Copyright (C) 2019 Linaro Ltd.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx7d.dtsi"
> > +
> > +/ {
> > + model = "96Boards Meerkat96 Board";
> > + compatible = "novtech,imx7d-meerkat96", "fsl,imx7d";
> > +
> > + chosen {
> > + stdout-path = &uart6;
> > + };
> > +
> > + memory@80000000 {
> > + device_type = "memory";
> > + reg = <0x80000000 0x20000000>; /* 512MB */
> > + };
> > +
> > + reg_wlreg_on: regulator-wlreg-on {
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wlreg_on>;
> > + regulator-name = "wlreg_on";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + startup-delay-us = <100>;
> > + gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > +
> > + reg_3p3v: regulator-3p3v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "3P3V";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_otg1_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + };
> > +
> > + reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_otg2_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + sw1a_reg: sw1a {
> > + compatible = "regulator-fixed";
>
> Actually I was wrong here. This is not a fixed regulator node as the voltage
> level varies. Since there is no PMIC support exist now, can I remove this node?
> Or I should make it as fixed 0.7v?

I dropped it (&cpu0 as well) and applied both patches. You can add it
later when you have the right information about it.

Shawn

\
 
 \ /
  Last update: 2019-06-18 09:56    [W:0.078 / U:0.176 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site