lkml.org 
[lkml]   [2019]   [Jun]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/2] staging: kpc2000: remove unnecessary comments in kp2000_pcie_probe
Date
Much of the code comments in kp2000_pcie_probe just repeats the code and
does not add any additional information. Delete them and make sure that
comments still left in the function all use the same style.

Signed-off-by: Simon Sandström <simon@nikanor.nu>
---
drivers/staging/kpc2000/kpc2000/core.c | 38 ++++----------------------
1 file changed, 5 insertions(+), 33 deletions(-)

diff --git a/drivers/staging/kpc2000/kpc2000/core.c b/drivers/staging/kpc2000/kpc2000/core.c
index ee6b9be7127d..6a5999e8ff4e 100644
--- a/drivers/staging/kpc2000/kpc2000/core.c
+++ b/drivers/staging/kpc2000/kpc2000/core.c
@@ -311,18 +311,12 @@ static int kp2000_pcie_probe(struct pci_dev *pdev,
unsigned long dma_bar_phys_len;
u16 regval;

- /*
- * Step 1: Allocate a struct for the pcard
- */
pcard = kzalloc(sizeof(*pcard), GFP_KERNEL);
if (!pcard)
return -ENOMEM;
dev_dbg(&pdev->dev, "probe: allocated struct kp2000_device @ %p\n",
pcard);

- /*
- * Step 2: Initialize trivial pcard elements
- */
err = ida_simple_get(&card_num_ida, 1, INT_MAX, GFP_KERNEL);
if (err < 0) {
dev_err(&pdev->dev, "probe: failed to get card number (%d)\n",
@@ -338,9 +332,6 @@ static int kp2000_pcie_probe(struct pci_dev *pdev,
pcard->pdev = pdev;
pci_set_drvdata(pdev, pcard);

- /*
- * Step 3: Enable PCI device
- */
err = pci_enable_device(pcard->pdev);
if (err) {
dev_err(&pcard->pdev->dev,
@@ -349,9 +340,7 @@ static int kp2000_pcie_probe(struct pci_dev *pdev,
goto err_remove_ida;
}

- /*
- * Step 4: Setup the Register BAR
- */
+ /* Setup the Register BAR */
reg_bar_phys_addr = pci_resource_start(pcard->pdev, REG_BAR);
reg_bar_phys_len = pci_resource_len(pcard->pdev, REG_BAR);

@@ -381,9 +370,7 @@ static int kp2000_pcie_probe(struct pci_dev *pdev,
reg_bar_phys_len - 1;
pcard->regs_base_resource.flags = IORESOURCE_MEM;

- /*
- * Step 5: Setup the DMA BAR
- */
+ /* Setup the DMA BAR */
dma_bar_phys_addr = pci_resource_start(pcard->pdev, DMA_BAR);
dma_bar_phys_len = pci_resource_len(pcard->pdev, DMA_BAR);

@@ -415,9 +402,7 @@ static int kp2000_pcie_probe(struct pci_dev *pdev,
dma_bar_phys_len - 1;
pcard->dma_base_resource.flags = IORESOURCE_MEM;

- /*
- * Step 6: System Regs
- */
+ /* Read System Regs */
pcard->sysinfo_regs_base = pcard->regs_bar_base;
err = read_system_regs(pcard);
if (err)
@@ -427,11 +412,9 @@ static int kp2000_pcie_probe(struct pci_dev *pdev,
writeq(0xFFFFFFFFFFFFFFFF,
pcard->sysinfo_regs_base + REG_INTERRUPT_MASK);

- /*
- * Step 7: Configure PCI thingies
- */
// let the card master PCIe
pci_set_master(pcard->pdev);
+
// enable IO and mem if not already done
pci_read_config_word(pcard->pdev, PCI_COMMAND, &regval);
regval |= (PCI_COMMAND_IO | PCI_COMMAND_MEMORY);
@@ -466,9 +449,6 @@ static int kp2000_pcie_probe(struct pci_dev *pdev,
dev_dbg(&pcard->pdev->dev,
"Using DMA mask %0llx\n", dma_get_mask(PCARD_TO_DEV(pcard)));

- /*
- * Step 8: Configure IRQs
- */
err = pci_enable_msi(pcard->pdev);
if (err < 0)
goto err_unmap_dma;
@@ -481,25 +461,17 @@ static int kp2000_pcie_probe(struct pci_dev *pdev,
goto err_disable_msi;
}

- /*
- * Step 9: Setup sysfs attributes
- */
err = sysfs_create_files(&pdev->dev.kobj, kp_attr_list);
if (err) {
dev_err(&pdev->dev, "Failed to add sysfs files: %d\n", err);
goto err_free_irq;
}

- /*
- * Step 10: Probe cores
- */
err = kp2000_probe_cores(pcard);
if (err)
goto err_remove_sysfs;

- /*
- * Step 11: Enable IRQs in HW
- */
+ /* Enable IRQs in HW */
writel(KPC_DMA_CARD_IRQ_ENABLE | KPC_DMA_CARD_USER_INTERRUPT_MODE,
pcard->dma_common_regs);

--
2.20.1
\
 
 \ /
  Last update: 2019-06-12 15:59    [W:0.046 / U:17.160 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site