lkml.org 
[lkml]   [2019]   [Jun]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/2] dt-bindings: net: wiznet: add w5x00 support
Date
Add bindings for Wiznet's w5x00 series of SPI interfaced Ethernet chips.

Based on the bindings for microchip,enc28j60.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---

Changes since v1:
- one compatible sting per line
- use correct 'ethenet@0' phandle name

.../devicetree/bindings/net/wiznet,w5x00.txt | 51 +++++++++++++++++++
1 file changed, 51 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/wiznet,w5x00.txt

diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
new file mode 100644
index 000000000000..901946dea3de
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
@@ -0,0 +1,51 @@
+* Wiznet w5x00
+
+This is a standalone 10/100 MBit Ethernet controller with SPI interface.
+
+For each device connected to a SPI bus, define a child node within
+the SPI master node.
+
+Required properties:
+- compatible: Should be one of the following strings:
+ "wiznet,w5100"
+ "wiznet,w5200"
+ "wiznet,w5500"
+- reg: Specify the SPI chip select the chip is wired to.
+- interrupts: Specify the interrupt index within the interrupt controller (referred
+ to above in interrupt-parent) and interrupt type. w5x00 natively
+ generates falling edge interrupts, however, additional board logic
+ might invert the signal.
+- pinctrl-names: List of assigned state names, see pinctrl binding documentation.
+- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line,
+ see also generic and your platform specific pinctrl binding
+ documentation.
+
+Optional properties:
+- spi-max-frequency: Maximum frequency of the SPI bus when accessing the w5500.
+ According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however,
+ board designs may need to limit this value.
+- local-mac-address: See ethernet.txt in the same directory.
+
+
+Example (for Raspberry Pi with pin control stuff for GPIO irq):
+
+&spi {
+ ethernet@0: w5500@0 {
+ compatible = "wiznet,w5500";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&eth1_pins>;
+ interrupt-parent = <&gpio>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ spi-max-frequency = <30000000>;
+ };
+};
+
+&gpio {
+ eth1_pins: eth1_pins {
+ brcm,pins = <25>;
+ brcm,function = <0>; /* in */
+ brcm,pull = <0>; /* none */
+ };
+};
+
--
2.21.0
\
 
 \ /
  Last update: 2019-06-12 14:27    [W:0.040 / U:20.084 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site