lkml.org 
[lkml]   [2019]   [Jun]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] drm/bridge: dw-hdmi: Use automatic CTS generation mode when using non-AHB audio
Date
When using an I2S source using a different clock source (usually the I2S
audio HW uses dedicated PLLs, different from the HDMI PHY PLL), fixed
CTS values will cause some frequent audio drop-out and glitches as
reported on Amlogic, Allwinner and Rockchip SoCs setups.

Setting the CTS in automatic mode will let the HDMI controller generate
automatically the CTS value to match the input audio clock.

The DesignWare DW-HDMI User Guide explains:
For Automatic CTS generation
Write "0" on the bit field "CTS_manual", Register 0x3205: AUD_CTS3

The DesignWare DW-HDMI Databook explains :
If "CTS_manual" bit equals 0b this registers contains "audCTS[19:0]"
generated by the Cycle time counter according to specified timing.

Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 44 +++++++++++++++--------
1 file changed, 29 insertions(+), 15 deletions(-)

diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
index c68b6ed1bb35..6458c3a31d23 100644
--- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
+++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
@@ -437,8 +437,14 @@ static void hdmi_set_cts_n(struct dw_hdmi *hdmi, unsigned int cts,
/* nshift factor = 0 */
hdmi_modb(hdmi, 0, HDMI_AUD_CTS3_N_SHIFT_MASK, HDMI_AUD_CTS3);

- hdmi_writeb(hdmi, ((cts >> 16) & HDMI_AUD_CTS3_AUDCTS19_16_MASK) |
- HDMI_AUD_CTS3_CTS_MANUAL, HDMI_AUD_CTS3);
+ /* Use automatic CTS generation mode when CTS is not set */
+ if (cts)
+ hdmi_writeb(hdmi, ((cts >> 16) &
+ HDMI_AUD_CTS3_AUDCTS19_16_MASK) |
+ HDMI_AUD_CTS3_CTS_MANUAL,
+ HDMI_AUD_CTS3);
+ else
+ hdmi_writeb(hdmi, 0, HDMI_AUD_CTS3);
hdmi_writeb(hdmi, (cts >> 8) & 0xff, HDMI_AUD_CTS2);
hdmi_writeb(hdmi, cts & 0xff, HDMI_AUD_CTS1);

@@ -508,24 +514,32 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
{
unsigned long ftdms = pixel_clk;
unsigned int n, cts;
+ u8 config3;
u64 tmp;

n = hdmi_compute_n(sample_rate, pixel_clk);

- /*
- * Compute the CTS value from the N value. Note that CTS and N
- * can be up to 20 bits in total, so we need 64-bit math. Also
- * note that our TDMS clock is not fully accurate; it is accurate
- * to kHz. This can introduce an unnecessary remainder in the
- * calculation below, so we don't try to warn about that.
- */
- tmp = (u64)ftdms * n;
- do_div(tmp, 128 * sample_rate);
- cts = tmp;
+ config3 = hdmi_readb(hdmi, HDMI_CONFIG3_ID);

- dev_dbg(hdmi->dev, "%s: fs=%uHz ftdms=%lu.%03luMHz N=%d cts=%d\n",
- __func__, sample_rate, ftdms / 1000000, (ftdms / 1000) % 1000,
- n, cts);
+ /* Only compute CTS when using internal AHB audio */
+ if (config3 & HDMI_CONFIG3_AHBAUDDMA) {
+ /*
+ * Compute the CTS value from the N value. Note that CTS and N
+ * can be up to 20 bits in total, so we need 64-bit math. Also
+ * note that our TDMS clock is not fully accurate; it is
+ * accurate to kHz. This can introduce an unnecessary remainder
+ * in the calculation below, so we don't try to warn about that.
+ */
+ tmp = (u64)ftdms * n;
+ do_div(tmp, 128 * sample_rate);
+ cts = tmp;
+
+ dev_dbg(hdmi->dev, "%s: fs=%uHz ftdms=%lu.%03luMHz N=%d cts=%d\n",
+ __func__, sample_rate,
+ ftdms / 1000000, (ftdms / 1000) % 1000,
+ n, cts);
+ } else
+ cts = 0;

spin_lock_irq(&hdmi->audio_lock);
hdmi->audio_n = n;
--
2.21.0
\
 
 \ /
  Last update: 2019-06-12 10:53    [W:0.059 / U:5.088 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site