lkml.org 
[lkml]   [2019]   [Jun]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] usb: dwc3: meson-g12a: Add support for IRQ based OTG switching
Hi Neil,

On Tue, Jun 11, 2019 at 3:58 PM Neil Armstrong <narmstrong@baylibre.com> wrote:
>
> Add support for the OTG ID change interrupt to switch between Host
> and Device mode.
>
> Tested on the Hardkernel Odroid-N2 board.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
with the three questions/comments below answered/addressed:
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

> ---
> drivers/usb/dwc3/dwc3-meson-g12a.c | 32 ++++++++++++++++++++++++++++--
> 1 file changed, 30 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
> index 2aec31a2eacb..e5c5ad0d529e 100644
> --- a/drivers/usb/dwc3/dwc3-meson-g12a.c
> +++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
the comment block at the start of the driver file also contains a
"TOFIX" which points to the missing IRQ handling
can you please also drop that TOFIX comment in lines 15/16?

> @@ -348,6 +348,22 @@ static enum usb_role dwc3_meson_g12a_role_get(struct device *dev)
> USB_ROLE_HOST : USB_ROLE_DEVICE;
> }
>
> +static irqreturn_t dwc3_meson_g12a_irq_thread(int irq, void *data)
> +{
> + struct dwc3_meson_g12a *priv = data;
> + enum phy_mode otg_id;
> +
> + otg_id = dwc3_meson_g12a_get_id(priv);
> + if (otg_id != priv->otg_phy_mode) {
> + if (dwc3_meson_g12a_otg_mode_set(priv, otg_id))
> + dev_warn(priv->dev, "Failed to switch OTG mode\n");
> + }
> +
> + regmap_update_bits(priv->regmap, USB_R5, USB_R5_ID_DIG_IRQ, 0);
> +
> + return IRQ_HANDLED;
> +}
> +
> static struct device *dwc3_meson_g12_find_child(struct device *dev,
> const char *compatible)
> {
> @@ -374,7 +390,7 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
> void __iomem *base;
> struct resource *res;
> enum phy_mode otg_id;
> - int ret, i;
> + int ret, i, irq;
>
> priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> if (!priv)
> @@ -436,6 +452,19 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
> /* Get dr_mode */
> priv->otg_mode = usb_get_dr_mode(dev);
>
> + if (priv->otg_mode == USB_DR_MODE_OTG) {
> + /* Ack irq before registering */
> + regmap_update_bits(priv->regmap, USB_R5,
> + USB_R5_ID_DIG_IRQ, 0);
I assume that either the IRQ line is:
- always enabled
- enabled when (USB_R5_ID_DIG_EN_0 | USB_R5_ID_DIG_EN_1 |
USB_R5_ID_DIG_TH_MASK) are set (which we already do in
dwc3_meson_g12a_usb_init)

> + irq = platform_get_irq(pdev, 0);
do we need to check the IRQ before trying to request it?
drivers/gpu/drm/meson/meson_dw_hdmi.c and drivers/usb/dwc3/host.c for
example error out if irq number is lower than 0

(it's great to see that this only required a small patch to make it work :))


Martin

\
 
 \ /
  Last update: 2019-06-11 20:09    [W:0.050 / U:8.196 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site