lkml.org 
[lkml]   [2019]   [Jun]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/7] arm64: dts: actions: Add uSD and eMMC support for Bubblegum96

Hi Andreas,

On Mon, Jun 10, 2019 at 04:08:26PM +0200, Andreas Färber wrote:
> Hi Mani,
>
> Am 08.06.19 um 21:53 schrieb Manivannan Sadhasivam:
> > Add uSD and eMMC support for Bubblegum96 board based on Actions Semi
> > Owl SoC.
>
> What information does "based on Actions Semi Owl SoC" give us? :)
> The board name should be unique enough - Owl is a family of SoCs,
> "actions:" is in the subject and "s900-" is in the filename.
>

Makes sense!

> > SD0 is connected to uSD slot and SD2 is connected to eMMC.
>
> Suggest to add that as comments above the two nodes instead.
>

Okay.

> > Since there is no PMIC support added yet, fixed regulator has been
> > used as a regulator node.
>
> Fine with me - maybe add a comment and make sure it's aligned with the
> schematics naming wrt PMIC.
>

Okay.

> >
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > ---
> > .../boot/dts/actions/s900-bubblegum-96.dts | 50 +++++++++++++++++++
> > 1 file changed, 50 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
> > index 732daaa6e9d3..3b596d72de25 100644
> > --- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
> > +++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
> > @@ -13,6 +13,9 @@
> >
> > aliases {
> > serial5 = &uart5;
> > + mmc0 = &mmc0;
> > + mmc1 = &mmc1;
> > + mmc2 = &mmc2;
>
> Sort them alphabetically?
>

Ack.

> > };
> >
> > chosen {
> > @@ -23,6 +26,14 @@
> > device_type = "memory";
> > reg = <0x0 0x0 0x0 0x80000000>;
> > };
> > +
> > + reg_3p1v: regulator-3p1v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "fixed-3.1V";
> > + regulator-min-microvolt = <3100000>;
> > + regulator-max-microvolt = <3100000>;
> > + regulator-always-on;
> > + };
> > };
> >
> > &i2c0 {
> > @@ -241,6 +252,45 @@
> > bias-pull-up;
> > };
> > };
> > +
> > + mmc0_default: mmc0_default {
> > + pinmux {
> > + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
> > + "sd0_cmd_mfp", "sd0_clk_mfp";
> > + function = "sd0";
> > + };
> > + };
> > +
> > + mmc2_default: mmc2_default {
> > + pinmux {
> > + groups = "nand0_d0_ceb3_mfp";
> > + function = "sd2";
> > + };
> > + };
>
> Wouldn't it make more sense to move these and the below pinctrl-* to
> s900.dtsi for sharing with other theoretical boards? I really dislike
> the imx model where pin muxing is duplicated into each individual board.
>

Matter of taste. IMO pinctrl config belongs to the board design and I don't
wanna dump all combinations in the soc dtsi.

Thanks,
Mani

> Regards,
> Andreas
>
> > +};
> > +
> > +&mmc0 {
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc0_default>;
> > + no-sdio;
> > + no-mmc;
> > + no-1-8-v;
> > + cd-gpios = <&pinctrl 120 GPIO_ACTIVE_LOW>;
> > + bus-width = <4>;
> > + vmmc-supply = <&reg_3p1v>;
> > + vqmmc-supply = <&reg_3p1v>;
> > +};
> > +
> > +&mmc2 {
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc2_default>;
> > + no-sdio;
> > + no-sd;
> > + non-removable;
> > + bus-width = <8>;
> > + vmmc-supply = <&reg_3p1v>;
> > };
> >
> > &timer {
>
> --
> SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
> GF: Felix Imendörffer, Mary Higgins, Sri Rasiah
> HRB 21284 (AG Nürnberg)

\
 
 \ /
  Last update: 2019-06-10 18:11    [W:1.330 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site