lkml.org 
[lkml]   [2019]   [Jun]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v1 3/4] Bluetooth: btmtkuart: add an implementation for boot-gpios property
Date
From: Sean Wang <sean.wang@mediatek.com>

Not every platform has the pinctrl device integrates the GPIO the function
such as MT7621 whose pinctrl and GPIO are separate hardware so the driver
adds additional boot-gpios to let the MT766[3,8]U can enter the proper boot
mode by gpiod for such platform.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
drivers/bluetooth/btmtkuart.c | 34 +++++++++++++++++++++++++---------
1 file changed, 25 insertions(+), 9 deletions(-)

diff --git a/drivers/bluetooth/btmtkuart.c b/drivers/bluetooth/btmtkuart.c
index f5dbeec8e274..1257149cfdc4 100644
--- a/drivers/bluetooth/btmtkuart.c
+++ b/drivers/bluetooth/btmtkuart.c
@@ -119,6 +119,7 @@ struct btmtkuart_dev {

struct regulator *vcc;
struct gpio_desc *reset;
+ struct gpio_desc *boot;
struct pinctrl *pinctrl;
struct pinctrl_state *pins_runtime;
struct pinctrl_state *pins_boot;
@@ -911,6 +912,13 @@ static int btmtkuart_parse_dt(struct serdev_device *serdev)
return err;
}

+ bdev->boot = devm_gpiod_get_optional(&serdev->dev, "boot",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(bdev->boot)) {
+ err = PTR_ERR(bdev->boot);
+ return err;
+ }
+
bdev->pinctrl = devm_pinctrl_get(&serdev->dev);
if (IS_ERR(bdev->pinctrl)) {
err = PTR_ERR(bdev->pinctrl);
@@ -919,8 +927,10 @@ static int btmtkuart_parse_dt(struct serdev_device *serdev)

bdev->pins_boot = pinctrl_lookup_state(bdev->pinctrl,
"default");
- if (IS_ERR(bdev->pins_boot)) {
+ if (IS_ERR(bdev->pins_boot) && !bdev->boot) {
err = PTR_ERR(bdev->pins_boot);
+ dev_err(&serdev->dev,
+ "Should assign RXD to LOW at boot stage\n");
return err;
}

@@ -996,8 +1006,14 @@ static int btmtkuart_probe(struct serdev_device *serdev)
set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);

if (btmtkuart_is_standalone(bdev)) {
- /* Switch to the specific pin state for the booting requires */
- pinctrl_select_state(bdev->pinctrl, bdev->pins_boot);
+ if (bdev->boot) {
+ gpiod_set_value_cansleep(bdev->boot, 1);
+ } else {
+ /* Switch to the specific pin state for the booting
+ * requires.
+ */
+ pinctrl_select_state(bdev->pinctrl, bdev->pins_boot);
+ }

/* Power on */
err = regulator_enable(bdev->vcc);
@@ -1017,6 +1033,10 @@ static int btmtkuart_probe(struct serdev_device *serdev)
* mode the device requires for UART transfers.
*/
msleep(50);
+
+ if (bdev->boot)
+ devm_gpiod_put(&serdev->dev, bdev->boot);
+
pinctrl_select_state(bdev->pinctrl, bdev->pins_runtime);

/* A standalone device doesn't depends on power domain on SoC,
@@ -1037,10 +1057,8 @@ static int btmtkuart_probe(struct serdev_device *serdev)
return 0;

err_regulator_disable:
- if (btmtkuart_is_standalone(bdev)) {
- pinctrl_select_state(bdev->pinctrl, bdev->pins_boot);
+ if (btmtkuart_is_standalone(bdev))
regulator_disable(bdev->vcc);
- }

return err;
}
@@ -1050,10 +1068,8 @@ static void btmtkuart_remove(struct serdev_device *serdev)
struct btmtkuart_dev *bdev = serdev_device_get_drvdata(serdev);
struct hci_dev *hdev = bdev->hdev;

- if (btmtkuart_is_standalone(bdev)) {
- pinctrl_select_state(bdev->pinctrl, bdev->pins_boot);
+ if (btmtkuart_is_standalone(bdev))
regulator_disable(bdev->vcc);
- }

hci_unregister_dev(hdev);
hci_free_dev(hdev);
--
2.17.1
\
 
 \ /
  Last update: 2019-06-02 03:05    [W:0.058 / U:5.328 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site