lkml.org 
[lkml]   [2019]   [May]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 4.19 15/99] USB: dummy-hcd: Fix failure to give back unlinked URBs
    Date
    From: Alan Stern <stern@rowland.harvard.edu>

    commit fc834e607ae3d18e1a20bca3f9a2d7f52ea7a2be upstream.

    The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
    would never give back an unlinked URB. This causes usb_kill_urb() to
    hang, leading to WARNINGs and unkillable threads.

    In dummy-hcd, all URBs are given back by the dummy_timer() routine as
    it scans through the list of pending URBS. Failure to give back URBs
    can be caused by failure to start or early exit from the scanning
    loop. The code currently has two such pathways: One is triggered when
    an unsupported bus transfer speed is encountered, and the other by
    exhausting the simulated bandwidth for USB transfers during a frame.

    This patch removes those two paths, thereby allowing all unlinked URBs
    to be given back in a timely manner. It adds a check for the bus
    speed when the gadget first starts running, so that dummy_timer() will
    never thereafter encounter an unsupported speed. And it prevents the
    loop from exiting as soon as the total bandwidth has been used up (the
    scanning loop continues, giving back unlinked URBs as they are found,
    but not transferring any more data).

    Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
    to help track down the source of the bug.

    Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
    Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
    CC: <stable@vger.kernel.org>
    Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

    ---
    drivers/usb/gadget/udc/dummy_hcd.c | 19 +++++++++++++++----
    1 file changed, 15 insertions(+), 4 deletions(-)

    --- a/drivers/usb/gadget/udc/dummy_hcd.c
    +++ b/drivers/usb/gadget/udc/dummy_hcd.c
    @@ -979,8 +979,18 @@ static int dummy_udc_start(struct usb_ga
    struct dummy_hcd *dum_hcd = gadget_to_dummy_hcd(g);
    struct dummy *dum = dum_hcd->dum;

    - if (driver->max_speed == USB_SPEED_UNKNOWN)
    + switch (g->speed) {
    + /* All the speeds we support */
    + case USB_SPEED_LOW:
    + case USB_SPEED_FULL:
    + case USB_SPEED_HIGH:
    + case USB_SPEED_SUPER:
    + break;
    + default:
    + dev_err(dummy_dev(dum_hcd), "Unsupported driver max speed %d\n",
    + driver->max_speed);
    return -EINVAL;
    + }

    /*
    * SLAVE side init ... the layer above hardware, which
    @@ -1784,9 +1794,10 @@ static void dummy_timer(struct timer_lis
    /* Bus speed is 500000 bytes/ms, so use a little less */
    total = 490000;
    break;
    - default:
    + default: /* Can't happen */
    dev_err(dummy_dev(dum_hcd), "bogus device speed\n");
    - return;
    + total = 0;
    + break;
    }

    /* FIXME if HZ != 1000 this will probably misbehave ... */
    @@ -1828,7 +1839,7 @@ restart:

    /* Used up this frame's bandwidth? */
    if (total <= 0)
    - break;
    + continue;

    /* find the gadget's ep for this request (if configured) */
    address = usb_pipeendpoint (urb->pipe);

    \
     
     \ /
      Last update: 2019-05-06 16:39    [W:4.190 / U:0.004 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site