lkml.org 
[lkml]   [2019]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: r8169: Link only up after 16 s (A link change request failed with some changes committed already. Interface enp3s0 may have been left with an inconsistent configuration, please check.)
From
Date
On 23.05.2019 13:00, Paul Menzel wrote:
> Dear Linux folks,
>
>
> I optimized the Linux kernel configuration on my ASRock E350M1, and it now
> boots really fast.
>
> Unfortunately, that seems to cause the network driver to hit some corner
> case, so that the link is supposedly down, although it should be up. The
> cable is plugged in the whole time.
>
> ```
> [ 2.990757] libphy: r8169: probed
> [ 2.992661] r8169 0000:03:00.0 eth0: RTL8168e/8111e, bc:5f:f4:c8:d3:98, XID 2c2, IRQ 28
> [ 2.992669] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
> [ 3.294484] usb 5-2: new low-speed USB device number 2 using ohci-pci
> [ 3.458711] usb 5-2: New USB device found, idVendor=1241, idProduct=1122, bcdDevice= 1.00
> [ 3.458718] usb 5-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> [ 3.485065] input: HID 1241:1122 as /devices/pci0000:00/0000:00:12.0/usb5/5-2/5-2:1.0/0003:1241:1122.0001/input/input14
> [ 3.485320] hid-generic 0003:1241:1122.0001: input,hidraw0: USB HID v1.00 Mouse [HID 1241:1122] on usb-0000:00:12.0-2/input0
> [ 3.967622] random: crng init done
> [ 3.967628] random: 7 urandom warning(s) missed due to ratelimiting
> [ 4.323449] r8169 0000:03:00.0 enp3s0: renamed from eth0
> [ 4.363774] RTL8211DN Gigabit Ethernet r8169-300:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
> [ 4.576887] r8169 0000:03:00.0 enp3s0: Link is Down
> [ 4.577167] A link change request failed with some changes committed already. Interface enp3s0 may have been left with an inconsistent configuration, please check.
> [ 16.377520] r8169 0000:03:00.0 enp3s0: Link is Up - 100Mbps/Full - flow control rx/tx
> [ 16.377553] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
> ```
>
> It happens with all Linux kernels I tried. Please find all Linux
> messages attached.
>
> Could you please tell me, how this can be debugged and solved?
>
This warning is triggered by errors in do_setlink() in net/core/rtnetlink.c
I'd say:
1. Which kernel config options did you change as part of the optimization?
(If I understand you correctly the warning didn't pop up before.)
2. Try to find out which call in do_setlink() fails and which errno is returned.

>
> Kind regards,
>
> Paul
>
Heiner

\
 
 \ /
  Last update: 2019-05-23 19:46    [W:0.110 / U:0.236 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site