lkml.org 
[lkml]   [2019]   [May]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [Intel-wired-lan] i40e X722 RSS problem with NAT-Traversal IPsec packets
From
On Fri, May 17, 2019 at 03:20:02PM -0700, Alexander Duyck wrote:
> I was hoping it would work too. It seemed like it should have been the
> answer since it definitely didn't seem right. Now it has me wondering
> about some of the other code in the driver.
>
> By any chance have you run anything like DPDK on any of the X722
> interfaces on this system recently? I ask because it occurs to me that
> if you had and it loaded something like a custom parsing profile it
> could cause issues similar to this.

I have never used DPDK on anything. I was hoping never to do so. :)

This system has so far booted Debian (with a 4.19 kernel) and our own OS
(which has a 4.9 kernel).

> A debugging step you might try would be to revert back to my earlier
> patch that only displayed the input mask instead of changing it. Once
> you have done that you could look at doing a full power cycle on the
> system by either physically disconnecting the power, or using the
> power switch on the power supply itself if one is available. It is
> necessary to disconnect the motherboard/NIC from power in order to
> fully clear the global state stored in the device as it is retained
> when the system is in standby.
>
> What I want to verify is if the input mask that we have ran into is
> the natural power-on input mask of if that is something that was
> overridden by something else. The mask change I made should be reset
> if the system loses power, and then it will either default back to the
> value with the 6's if that is it's natural state, or it will match
> what I had if it was not.
>
> Other than that I really can't think up too much else. I suppose there
> is the possibility of the NVM either setting up a DCB setting or
> HREGION register causing an override that is limiting the queues to 1.
> However, the likelihood of that should be really low.

Here is the register dump after a full power off:

40e: Intel(R) Ethernet Connection XL710 Network Driver - version 2.1.7-k
i40e: Copyright (c) 2013 - 2014 Intel Corporation.
i40e 0000:3d:00.0: fw 3.10.52896 api 1.6 nvm 4.00 0x80001577 1.1767.0
i40e 0000:3d:00.0: The driver for the device detected a newer version of the NVM image than expected. Please install the most recent version of the network driver.
i40e 0000:3d:00.0: MAC address: a4:bf:01:4e:0c:87
i40e 0000:3d:00.0: flow_type: 63 input_mask:0x0000000000004000
i40e 0000:3d:00.0: flow_type: 46 input_mask:0x0007fff800000000
i40e 0000:3d:00.0: flow_type: 45 input_mask:0x0007fff800000000
i40e 0000:3d:00.0: flow_type: 44 input_mask:0x0007ffff80000000
i40e 0000:3d:00.0: flow_type: 43 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 42 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 41 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 40 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 39 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 36 input_mask:0x0006060000000000
i40e 0000:3d:00.0: flow_type: 35 input_mask:0x0006060000000000
i40e 0000:3d:00.0: flow_type: 34 input_mask:0x0006060780000000
i40e 0000:3d:00.0: flow_type: 33 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow_type: 32 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow_type: 31 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow_type: 30 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow_type: 29 input_mask:0x0006060600000000
i40e 0000:3d:00.0: Features: PF-id[0] VSIs: 34 QP: 12 TXQ: 13 RSS VxLAN Geneve VEPA
i40e 0000:3d:00.1: fw 3.10.52896 api 1.6 nvm 4.00 0x80001577 1.1767.0
i40e 0000:3d:00.1: The driver for the device detected a newer version of the NVM image than expected. Please install the most recent version of the network driver.
i40e 0000:3d:00.1: MAC address: a4:bf:01:4e:0c:88
i40e 0000:3d:00.1: flow_type: 63 input_mask:0x0000000000004000
i40e 0000:3d:00.1: flow_type: 46 input_mask:0x0007fff800000000
i40e 0000:3d:00.1: flow_type: 45 input_mask:0x0007fff800000000
i40e 0000:3d:00.1: flow_type: 44 input_mask:0x0007ffff80000000
i40e 0000:3d:00.1: flow_type: 43 input_mask:0x0007fffe00000000
i40e 0000:3d:00.1: flow_type: 42 input_mask:0x0007fffe00000000
i40e 0000:3d:00.1: flow_type: 41 input_mask:0x0007fffe00000000
i40e 0000:3d:00.1: flow_type: 40 input_mask:0x0007fffe00000000
i40e 0000:3d:00.1: flow_type: 39 input_mask:0x0007fffe00000000
i40e 0000:3d:00.1: flow_type: 36 input_mask:0x0006060000000000
i40e 0000:3d:00.1: flow_type: 35 input_mask:0x0006060000000000
i40e 0000:3d:00.1: flow_type: 34 input_mask:0x0006060780000000
i40e 0000:3d:00.1: flow_type: 33 input_mask:0x0006060600000000
i40e 0000:3d:00.1: flow_type: 32 input_mask:0x0006060600000000
i40e 0000:3d:00.1: flow_type: 31 input_mask:0x0006060600000000
i40e 0000:3d:00.1: flow_type: 30 input_mask:0x0006060600000000
i40e 0000:3d:00.1: flow_type: 29 input_mask:0x0006060600000000
i40e 0000:3d:00.1: Features: PF-id[1] VSIs: 34 QP: 12 TXQ: 13 RSS VxLAN Geneve VEPA
i40e 0000:3d:00.1 eth2: NIC Link is Up, 1000 Mbps Full Duplex, Flow Control: None

Pretty sure that is identical to before.

If I dump the registers after doing the update I see this (just did a
reboot this time, not a power cycle):

i40e: Intel(R) Ethernet Connection XL710 Network Driver - version 2.1.7-k
i40e: Copyright (c) 2013 - 2014 Intel Corporation.
i40e 0000:3d:00.0: fw 3.10.52896 api 1.6 nvm 4.00 0x80001577 1.1767.0
i40e 0000:3d:00.0: The driver for the device detected a newer version of the NVM image than expected. Please install the most recent version of the network driver.
i40e 0000:3d:00.0: MAC address: a4:bf:01:4e:0c:87
i40e 0000:3d:00.0: flow_type: 63 input_mask:0x0000000000004000
i40e 0000:3d:00.0: flow_type: 46 input_mask:0x0007fff800000000
i40e 0000:3d:00.0: flow_type: 45 input_mask:0x0007fff800000000
i40e 0000:3d:00.0: flow_type: 44 input_mask:0x0007ffff80000000
i40e 0000:3d:00.0: flow_type: 43 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 42 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 41 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 40 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 39 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type: 36 input_mask:0x0006060000000000
i40e 0000:3d:00.0: flow_type: 35 input_mask:0x0006060000000000
i40e 0000:3d:00.0: flow_type: 34 input_mask:0x0006060780000000
i40e 0000:3d:00.0: flow_type: 33 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow_type: 32 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow_type: 31 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow_type: 30 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow_type: 29 input_mask:0x0006060600000000
i40e 0000:3d:00.0: flow type: 36 update input mask from:0x0006060000000000, to:0x0001801800000000
i40e 0000:3d:00.0: flow type: 35 update input mask from:0x0006060000000000, to:0x0001801800000000
i40e 0000:3d:00.0: flow type: 34 update input mask from:0x0006060780000000, to:0x0001801f80000000
i40e 0000:3d:00.0: flow type: 33 update input mask from:0x0006060600000000, to:0x0001801e00000000
i40e 0000:3d:00.0: flow type: 32 update input mask from:0x0006060600000000, to:0x0001801e00000000
i40e 0000:3d:00.0: flow type: 31 update input mask from:0x0006060600000000, to:0x0001801e00000000
i40e 0000:3d:00.0: flow type: 30 update input mask from:0x0006060600000000, to:0x0001801e00000000
i40e 0000:3d:00.0: flow type: 29 update input mask from:0x0006060600000000, to:0x0001801e00000000
i40e 0000:3d:00.0: flow_type after update: 63 input_mask:0x0000000000004000
i40e 0000:3d:00.0: flow_type after update: 46 input_mask:0x0007fff800000000
i40e 0000:3d:00.0: flow_type after update: 45 input_mask:0x0007fff800000000
i40e 0000:3d:00.0: flow_type after update: 44 input_mask:0x0007ffff80000000
i40e 0000:3d:00.0: flow_type after update: 43 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type after update: 42 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type after update: 41 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type after update: 40 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type after update: 39 input_mask:0x0007fffe00000000
i40e 0000:3d:00.0: flow_type after update: 36 input_mask:0x0001801800000000
i40e 0000:3d:00.0: flow_type after update: 35 input_mask:0x0001801800000000
i40e 0000:3d:00.0: flow_type after update: 34 input_mask:0x0001801f80000000
i40e 0000:3d:00.0: flow_type after update: 33 input_mask:0x0001801e00000000
i40e 0000:3d:00.0: flow_type after update: 32 input_mask:0x0001801e00000000
i40e 0000:3d:00.0: flow_type after update: 31 input_mask:0x0001801e00000000
i40e 0000:3d:00.0: flow_type after update: 30 input_mask:0x0001801e00000000
i40e 0000:3d:00.0: flow_type after update: 29 input_mask:0x0001801e00000000
i40e 0000:3d:00.0: Features: PF-id[0] VSIs: 34 QP: 12 TXQ: 13 RSS VxLAN Geneve VEPA

So at least it appears the update did apply.

--
Len Sorensen

\
 
 \ /
  Last update: 2019-05-21 17:16    [W:0.073 / U:1.540 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site