lkml.org 
[lkml]   [2019]   [May]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 2/2] mtd: nand: raw: brcmnand: fallback to detected ecc-strength, ecc-step-size
Will make the changes and send a V2 patch.

On Mon, May 20, 2019 at 8:44 AM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
>
> Hi Kamal,
>
> Kamal Dasu <kdasu.kdev@gmail.com> wrote on Fri, 17 May 2019 14:29:55
> -0400:
>
> > This change supports nand-ecc-step-size and nand-ecc-strenght fields in
>
> strength
>
> > brcmnand dt node to be optional.
>
> DT ^ extra space
>
> > see: Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
> >
> > If both nand-ecc-strength and nand-ecc-step-size are not specified in
> > device tree node for NAND, nand_base driver does detect onfi ext ecc
>
> s/nand_base driver/the raw NAND layer/
> s/onfi/ONFI/
> s/ecc/ECC/
>
> What is "ext"? Please use plain English here.
>
> > info from ONFI extended parameter page for parts using ONFI >= 2.1. In
>
> s/info/information/
>
> > case of non-onfi NAND there could be a nand_id table entry with the ecc
>
> s/ecc/ECC/
>
> > info. If there is a valid device tree entry for nand-ecc-strength and
> > nand-ecc-step-size fields it still shall override the detected values.
> >
> > Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
> > ---
> > drivers/mtd/nand/raw/brcmnand/brcmnand.c | 10 ++++++++++
> > 1 file changed, 10 insertions(+)
> >
> > diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > index ce0b8ff..e967b30 100644
> > --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
> > @@ -2144,6 +2144,16 @@ static int brcmnand_setup_dev(struct brcmnand_host *host)
> > return -EINVAL;
> > }
> >
> > + if (!(chip->ecc.size > 0 && chip->ecc.strength > 0) &&
>
> Is the case where only size OR strength is valid handled?

Both strength and need to be valid, else the driver will behave like
before and will fail the probe.

>
> > + (chip->base.eccreq.strength > 0 &&
> > + chip->base.eccreq.step_size > 0)) {
> > + /* use detected ecc parameters */
>
> Use ECC
>
> > + chip->ecc.size = chip->base.eccreq.step_size;
> > + chip->ecc.strength = chip->base.eccreq.strength;
> > + pr_info("Using detected nand-ecc-step-size %d, nand-ecc-strength %d\n",
> > + chip->ecc.size, chip->ecc.strength);
> > + }
> > +
> > switch (chip->ecc.size) {
> > case 512:
> > if (chip->ecc.algo == NAND_ECC_HAMMING)
>
>
> Thanks,
> Miquèl

Kamal

\
 
 \ /
  Last update: 2019-05-20 19:33    [W:0.049 / U:47.260 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site