lkml.org 
[lkml]   [2019]   [May]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 2/6] dt-bindings: usb: add binding for Type-B GPIO connector driver
From
Date
On Tue, 2019-05-14 at 13:12 -0500, Rob Herring wrote:
> On Tue, May 14, 2019 at 04:47:19PM +0800, Chunfeng Yun wrote:
> > It's used to support dual role switch via GPIO when use Type-B
> > receptacle, typically the USB ID pin is connected to an input
> > GPIO pin
> >
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v5 changes:
> > 1. treat type-B connector as child device of USB controller's, but not
> > as a separate virtual device, suggested by Rob
> > 2. put connector's port node under connector node, suggested by Rob
> >
> > v4 no changes
> >
> > v3 changes:
> > 1. treat type-B connector as a virtual device, but not child device of
> > USB controller's
> >
> > v2 changes:
> > 1. new patch to make binding clear suggested by Hans
> > ---
> > .../bindings/usb/typeb-conn-gpio.txt | 42 +++++++++++++++++++
> > 1 file changed, 42 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt
> >
> > diff --git a/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt b/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt
> > new file mode 100644
> > index 000000000000..20dd3499a348
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt
> > @@ -0,0 +1,42 @@
> > +USB Type-B GPIO Connector
> > +
> > +This is used to switch dual role mode from the USB ID pin connected to
> > +an input GPIO pin.
> > +
> > +Required properties:
> > +- compatible : should include "linux,typeb-conn-gpio" and "usb-b-connector".
>
> I don't think we need "linux,typeb-conn-gpio".
Not all usb-b-connector child node need bind this driver, by adding the
new compatible can avoid unnecessary binding.

> A driver can decide to
> handle GPIO lines if they present
Yes, the driver, e.g. USB controller driver can do it, but here I want
to provide a common driver to handle this special case, like
extcon-usb-gpio driver does, and try to keep transparency from USB
controller driver.

> or we assume the parent device handles
> ID and/or Vbus if they are not present.
Yes, it will
>
> > +- id-gpios, vbus-gpios : either one of them must be present, and both
> > + can be present as well.
>
> Please clarify that vbus-gpios is an input to sense Vbus presence as an
> output it should be modelled as a regulator only.
Ok, will add more description.
>
> These should be added to usb-connector.txt.
Already add them in [1/6].
>
> The result of all this is you don't need this file. Just additions to
> usb-connector.txt.
Here add more constrains for id-gpios and vbus-gpios, at least one
should be present, although they are both optional, this is not true for
some cases, so not suitable to add into usb-connector.txt.
>
> > +- vbus-supply : can be present if needed when supports dual role mode or
> > + host mode.
> > + see connector/usb-connector.txt
> > +
> > +Sub-nodes:
> > +- port : should be present.
> > + see graph.txt
> > +
> > +Example:
> > +
> > +&mtu3 {
> > + status = "okay";
>
> Don't show status in examples.
Ok, will drop it.
>
> > +
> > + connector {
> > + compatible = "linux,typeb-conn-gpio", "usb-b-connector";
> > + label = "micro-USB";
> > + type = "micro";
> > + id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
> > + vbus-supply = <&usb_p0_vbus>;
> > +
> > + port {
> > + bconn_ep: endpoint@0 {
> > + remote-endpoint = <&usb_role_sw>;
> > + };
> > + };
> > + };
> > +
> > + port {
> > + usb_role_sw: endpoint@0 {
> > + remote-endpoint = <&bconn_ep>;
> > + };
> > + };
>
> When the host controller is the parent of the connector, you don't need
> the graph unless you're describing the alternate modes in Type-C.
Ok, got it.

Thanks a lot.

>
> > +};
> > --
> > 2.21.0
> >


\
 
 \ /
  Last update: 2019-05-15 11:37    [W:0.060 / U:90.904 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site