lkml.org 
[lkml]   [2019]   [Apr]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 08/12] arm64: dts: allwinner: h6: Add MMC1 pins
Hi,

On Tue, Apr 09, 2019 at 12:41:05AM +0200, Ondřej Jirman wrote:
> On Mon, Apr 08, 2019 at 09:43:27AM +0200, Maxime Ripard wrote:
> > On Sat, Apr 06, 2019 at 01:45:10AM +0200, megous@megous.com wrote:
> > > From: Ondrej Jirman <megous@megous.com>
> > >
> > > ---
> > > arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 9 +++++++++
> > > 1 file changed, 9 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> > > index 91fecab58836..dccad79da90c 100644
> > > --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> > > @@ -238,6 +238,15 @@
> > > bias-pull-up;
> > > };
> > >
> > > +
> >
> > Extra line
> >
> > > + mmc1_pins: mmc1-pins {
> > > + pins = "PG0", "PG1", "PG2", "PG3",
> > > + "PG4", "PG5";
> > > + function = "mmc1";
> > > + drive-strength = <30>;
> > > + bias-pull-up;
> > > + };
> > > +
> >
> > Is that the only muxing option?
>
> I don't think so. I believe someone can use a 1-bit interface (bus-width = <1>),
> and then some data pins will be free. This pinconfig is for 4-bit bus width
> setup.
>
> Though other SoCs (ex. H3, A83T) don't consider this possibility and make the
> 4-bit config the default pinctrl for mmc1. To add to the confusion, on these
> SoCs 4-bit pinconf is the default, but 1bit bus-width is the (implicit) default.
> This led to some confusion in the past.
>
> So we can either:
> - keep consistency with what is done elsewhere, and make this default, despite
> not being the only option,

What is done elsewhere is that if it's the only option, just call it
$controller_pins and make that the default. If it isn't, then call it
$(controller)_$(bank)_pins, and put it at the board level.

If it's not the only muxing option, then your name should be called
mmc1-pg-pins

> - or perhaps I can rename this to mmc1_bus_width4_pins, or somesuch, to make it
> more explicit, and keep it non-default.

We haven't encountered a case where the 1-bit bus was actually used,
so there's no need to take care of that.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2019-04-09 09:21    [W:0.049 / U:7.712 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site