lkml.org 
[lkml]   [2019]   [Apr]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] ARM: dts: sun50i: h6: Introduce Beelink GS1 board
Hi,

On Thu, Apr 04, 2019 at 02:45:04PM +0200, Clément Péron wrote:
> Beelink GS1 is an Allwinner H6 based TV box,
> which support:
> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> - GPU Mali-T720
> - 2GB LPDDR3 RAM
> - AXP805 PMIC
> - 1Gbps GMAC via RTL8211E
> - FN-Link 6222B-SRB Wifi/BT
> - 1x USB 2.0 Host and 1x USB 3.0 Host
> - HDMI port
> - S/PDIF Tx
> - IR receiver
> - 5V/2A DC power supply
>
> Signed-off-by: Clément Péron <peron.clem@gmail.com>
> ---
>
> Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on
> the OrangePi One Plus and Pine H64.
>
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 252 ++++++++++++++++++
> 2 files changed, 253 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index e4dce2f6fa3a..2dd806a3d5c9 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
> new file mode 100644
> index 000000000000..d927e7d33bf3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
> @@ -0,0 +1,252 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2019 Clément Péron <peron.clem@gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h6.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Beelink GS1";
> + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";

Please add that board to
Documentation/devicetree/bindings/arm/sunxi.yaml, it's new and in
linux-next.

> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + vmmc-supply = <&reg_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_pins>;

If those (mmc0 and mmc2_pins) are the only muxing options as their
names suggests, it should be set in the DTSI.

If not, the name of the pin group should be changed.

> + reg_cldo2: cldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-1";
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-2";
> + };

I don't see any SDIO bus declared, why do you need those regulators on?

Can you also declare the PIO regulators?

Thanks!
Maxmie

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2019-04-05 11:08    [W:0.066 / U:11.224 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site