lkml.org 
[lkml]   [2019]   [Apr]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] pci: aardvark: Wait for endpoint to be ready before training link
On Wed, Mar 13, 2019 at 10:37:52PM +0100, Remi Pommarel wrote:
> When configuring pcie reset pin from gpio (e.g. initially set by
> u-boot) to pcie function this pin goes low for a brief moment
> asserting the PERST# signal. Thus connected device enters fundamental
> reset process and link configuration can only begin after a minimal
> 100ms delay (see [1]).
>
> This makes sure that link is configured after at least 100ms from
> beginning of probe() callback (shortly after the reset pin function
> configuration switch through pinctrl subsytem).
>
> [1] "PCI Express Base Specification", REV. 2.1
> PCI Express, March 4 2009, 6.6.1 Conventional Reset

It would be nice to use a current reference, e.g., PCIe r4.0, sec
6.6.1.

> Signed-off-by: Remi Pommarel <repk@triplefau.lt>
> ---
> drivers/pci/controller/pci-aardvark.c | 17 ++++++++++++++---
> 1 file changed, 14 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/pci/controller/pci-aardvark.c b/drivers/pci/controller/pci-aardvark.c
> index a30ae7cf8e7e..70a1023d0ef1 100644
> --- a/drivers/pci/controller/pci-aardvark.c
> +++ b/drivers/pci/controller/pci-aardvark.c
> @@ -177,6 +177,9 @@
>
> #define PIO_TIMEOUT_MS 1
>
> +/* Endpoint can take up to 100ms to be ready after a reset */
> +#define ENDPOINT_RST_MS 100
> +
> #define LINK_WAIT_MAX_RETRIES 10
> #define LINK_WAIT_USLEEP_MIN 90000
> #define LINK_WAIT_USLEEP_MAX 100000
> @@ -242,8 +245,10 @@ static int advk_pcie_wait_for_link(struct advk_pcie *pcie)
> return -ETIMEDOUT;
> }
>
> -static void advk_pcie_setup_hw(struct advk_pcie *pcie)
> +static void
> +advk_pcie_setup_hw(struct advk_pcie *pcie, unsigned long ep_rdy_time)
> {
> + unsigned long now;
> u32 reg;
>
> /* Set to Direct mode */
> @@ -327,9 +332,12 @@ static void advk_pcie_setup_hw(struct advk_pcie *pcie)
> reg |= PIO_CTRL_ADDR_WIN_DISABLE;
> advk_writel(pcie, reg, PIO_CTRL);
>
> - /* Start link training */
> + /* Wait for endpoint to exit reset state and start link training */
> reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
> reg |= PCIE_CORE_LINK_TRAINING;
> + now = jiffies;
> + if (time_before(now, ep_rdy_time))
> + msleep(jiffies_to_msecs(ep_rdy_time - now));
> advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
>
> advk_pcie_wait_for_link(pcie);
> @@ -993,8 +1001,11 @@ static int advk_pcie_probe(struct platform_device *pdev)
> struct advk_pcie *pcie;
> struct resource *res;
> struct pci_host_bridge *bridge;
> + unsigned long ep_rdy_time;
> int ret, irq;
>
> + ep_rdy_time = jiffies + msecs_to_jiffies(ENDPOINT_RST_MS);

I think this is partly what Lorenzo is getting at, so at the risk of
being repetitious, there should be some connection between the point
where PERST# is deasserted and the point where you sample "jiffies".
Ideally you would sample "jiffies" immediately after the function call
that deasserts PERST#.

I see that you mention this connection in the commit log, but I don't
see a way to easily deduce it from the code. This looks like the very
first executable statement in the advk driver, so presumably there's
some implicit connection and ordering with the pinctrl driver.

> bridge = devm_pci_alloc_host_bridge(dev, sizeof(struct advk_pcie));
> if (!bridge)
> return -ENOMEM;
> @@ -1022,7 +1033,7 @@ static int advk_pcie_probe(struct platform_device *pdev)
> return ret;
> }
>
> - advk_pcie_setup_hw(pcie);
> + advk_pcie_setup_hw(pcie, ep_rdy_time);
>
> advk_sw_pci_bridge_init(pcie);
>
> --
> 2.20.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

\
 
 \ /
  Last update: 2019-04-25 18:31    [W:0.085 / U:0.412 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site