lkml.org 
[lkml]   [2019]   [Apr]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 3/5] i2c-mux-gpio: Save initial channel number to the idle data field
On Wed, Apr 24, 2019 at 09:26:22PM +0000, Peter Rosin wrote:
> On 2019-04-24 14:34, Serge Semin wrote:
> > In case if the idle state has been specified in the data structure,
> > the idle variable is left untouched as before, so to keep a default
> > channel number enabled in the mux idle state. But if a platform doesn't
> > specify which channel is going to be enabled by default, we as before
> > don't setup the deselect callback, but the initial state is saved in the
> > idle variable for further initialization. We can safely do this here
> > since that variable is used for initial state setting only, when no
> > idling lane is specified.
>
> While this subtlety is *maybe* ok, a comment about it belongs in the
> *code* where it will be seen when the next person makes changes.
>
> But why not extend the struct with the initial state? How many of
> these muxes do you expect to exist in a system? Multiplied by a
> couple of bytes. Who cares?
>

I actually thought about this when started working on the patchset.
That time saving the initial value in the idle variable seemed like a
good idea. I even put a small comment in the code about this.

Anyway lets add a new field to "struct gpiomux" structure and use
it as a container for initial value. It is also a good alternative.
I'll do this in a v2 patchset.

-Sergey

> Cheers,
> Peter
>
> >
> > The reason of this change is to prepare the code for future GPIOs request
> > path being split up into of- and plat- based methods. The idle variable
> > here is used as a container of the initial state for both of the paths in
> > case of idle-channel isn't specified.
> >
> > Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
> > ---
> > drivers/i2c/muxes/i2c-mux-gpio.c | 15 ++++++++-------
> > 1 file changed, 8 insertions(+), 7 deletions(-)
> >
> > diff --git a/drivers/i2c/muxes/i2c-mux-gpio.c b/drivers/i2c/muxes/i2c-mux-gpio.c
> > index a14fe132b0c3..535c83c43371 100644
> > --- a/drivers/i2c/muxes/i2c-mux-gpio.c
> > +++ b/drivers/i2c/muxes/i2c-mux-gpio.c
> > @@ -171,7 +171,6 @@ static int i2c_mux_gpio_probe(struct platform_device *pdev)
> > struct gpiomux *mux;
> > struct i2c_adapter *parent;
> > struct i2c_adapter *root;
> > - unsigned initial_state;
> > int i, ret;
> >
> > mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
> > @@ -204,12 +203,14 @@ static int i2c_mux_gpio_probe(struct platform_device *pdev)
> >
> > muxc->mux_locked = true;
> >
> > - if (mux->data.idle != I2C_MUX_GPIO_NO_IDLE) {
> > - initial_state = mux->data.idle;
> > + /*
> > + * Set descelect callback if idle state has been setup otherwise just
> > + * use the idle variable to store the initial muxer value.
> > + */
> > + if (mux->data.idle != I2C_MUX_GPIO_NO_IDLE)
> > muxc->deselect = i2c_mux_gpio_deselect;
> > - } else {
> > - initial_state = mux->data.values[0];
> > - }
> > + else
> > + mux->data.idle = mux->data.values[0];
> >
> > for (i = 0; i < mux->data.n_gpios; i++) {
> > struct device *gpio_dev;
> > @@ -224,7 +225,7 @@ static int i2c_mux_gpio_probe(struct platform_device *pdev)
> > }
> >
> > ret = gpio_direction_output(mux->gpio_base + mux->data.gpios[i],
> > - initial_state & (1 << i));
> > + mux->data.idle & (1 << i));
> > if (ret) {
> > dev_err(&pdev->dev,
> > "Failed to set direction of GPIO %d to output\n",
> >
>

\
 
 \ /
  Last update: 2019-04-25 17:54    [W:0.065 / U:25.564 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site