lkml.org 
[lkml]   [2019]   [Apr]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] serial: 8250-mtk: add follow control
Date
Add SW and HW follow control function.

Signed-off-by: Long Cheng <long.cheng@mediatek.com>
---
drivers/tty/serial/8250/8250_mtk.c | 60 ++++++++++++++++++++++--------------
1 file changed, 37 insertions(+), 23 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index c1fdbc0..959fd85 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -21,12 +21,14 @@

#include "8250.h"

-#define UART_MTK_HIGHS 0x09 /* Highspeed register */
-#define UART_MTK_SAMPLE_COUNT 0x0a /* Sample count register */
-#define UART_MTK_SAMPLE_POINT 0x0b /* Sample point register */
+#define MTK_UART_HIGHS 0x09 /* Highspeed register */
+#define MTK_UART_SAMPLE_COUNT 0x0a /* Sample count register */
+#define MTK_UART_SAMPLE_POINT 0x0b /* Sample point register */
#define MTK_UART_RATE_FIX 0x0d /* UART Rate Fix Register */
-
#define MTK_UART_DMA_EN 0x13 /* DMA Enable register */
+#define MTK_UART_RXTRI_AD 0x14 /* RX Trigger address */
+#define MTK_UART_FRACDIV_L 0x15 /* Fractional divider LSB address */
+#define MTK_UART_FRACDIV_M 0x16 /* Fractional divider MSB address */
#define MTK_UART_DMA_EN_TX 0x2
#define MTK_UART_DMA_EN_RX 0x5

@@ -46,6 +48,7 @@ enum dma_rx_status {
struct mtk8250_data {
int line;
unsigned int rx_pos;
+ unsigned int clk_count;
struct clk *uart_clk;
struct clk *bus_clk;
struct uart_8250_dma *dma;
@@ -196,9 +199,15 @@ static void mtk8250_shutdown(struct uart_port *port)
mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
+ unsigned short fraction_L_mapping[] = {
+ 0, 1, 0x5, 0x15, 0x55, 0x57, 0x57, 0x77, 0x7F, 0xFF, 0xFF
+ };
+ unsigned short fraction_M_mapping[] = {
+ 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3
+ };
struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned int baud, quot, fraction;
unsigned long flags;
- unsigned int baud, quot;

#ifdef CONFIG_SERIAL_8250_DMA
if (up->dma) {
@@ -214,7 +223,7 @@ static void mtk8250_shutdown(struct uart_port *port)
serial8250_do_set_termios(port, termios, old);

/*
- * Mediatek UARTs use an extra highspeed register (UART_MTK_HIGHS)
+ * Mediatek UARTs use an extra highspeed register (MTK_UART_HIGHS)
*
* We need to recalcualte the quot register, as the claculation depends
* on the vaule in the highspeed register.
@@ -230,18 +239,11 @@ static void mtk8250_shutdown(struct uart_port *port)
port->uartclk / 16 / UART_DIV_MAX,
port->uartclk);

- if (baud <= 115200) {
- serial_port_out(port, UART_MTK_HIGHS, 0x0);
+ if (baud < 115200) {
+ serial_port_out(port, MTK_UART_HIGHS, 0x0);
quot = uart_get_divisor(port, baud);
- } else if (baud <= 576000) {
- serial_port_out(port, UART_MTK_HIGHS, 0x2);
-
- /* Set to next lower baudrate supported */
- if ((baud == 500000) || (baud == 576000))
- baud = 460800;
- quot = DIV_ROUND_UP(port->uartclk, 4 * baud);
} else {
- serial_port_out(port, UART_MTK_HIGHS, 0x3);
+ serial_port_out(port, MTK_UART_HIGHS, 0x3);
quot = DIV_ROUND_UP(port->uartclk, 256 * baud);
}

@@ -258,17 +260,29 @@ static void mtk8250_shutdown(struct uart_port *port)
/* reset DLAB */
serial_port_out(port, UART_LCR, up->lcr);

- if (baud > 460800) {
+ if (baud >= 115200) {
unsigned int tmp;

- tmp = DIV_ROUND_CLOSEST(port->uartclk, quot * baud);
- serial_port_out(port, UART_MTK_SAMPLE_COUNT, tmp - 1);
- serial_port_out(port, UART_MTK_SAMPLE_POINT,
- (tmp - 2) >> 1);
+ tmp = (port->uartclk / (baud * quot)) - 1;
+ serial_port_out(port, MTK_UART_SAMPLE_COUNT, tmp);
+ serial_port_out(port, MTK_UART_SAMPLE_POINT,
+ (tmp >> 1) - 1);
+
+ /*count fraction to set fractoin register */
+ fraction = ((port->uartclk * 100) / baud / quot) % 100;
+ fraction = DIV_ROUND_CLOSEST(fraction, 10);
+ serial_port_out(port, MTK_UART_FRACDIV_L,
+ fraction_L_mapping[fraction]);
+ serial_port_out(port, MTK_UART_FRACDIV_M,
+ fraction_M_mapping[fraction]);
} else {
- serial_port_out(port, UART_MTK_SAMPLE_COUNT, 0x00);
- serial_port_out(port, UART_MTK_SAMPLE_POINT, 0xff);
+ serial_port_out(port, MTK_UART_SAMPLE_COUNT, 0x00);
+ serial_port_out(port, MTK_UART_SAMPLE_POINT, 0xff);
+ serial_port_out(port, MTK_UART_FRACDIV_L, 0x00);
+ serial_port_out(port, MTK_UART_FRACDIV_M, 0x00);
}
+ if (uart_console(port))
+ up->port.cons->cflag = termios->c_cflag;

spin_unlock_irqrestore(&port->lock, flags);
/* Don't rewrite B0 */
--
1.7.9.5
\
 
 \ /
  Last update: 2019-04-25 10:42    [W:0.044 / U:35.984 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site