lkml.org 
[lkml]   [2019]   [Apr]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 5/7] mmc: meson-gx: avoid clock glitch when switching to DDR modes
Hi Jerome,

On Fri, Apr 19, 2019 at 10:53 AM Jerome Brunet <jbrunet@baylibre.com> wrote:
>
> On Thu, 2019-04-18 at 23:15 +0200, Jerome Brunet wrote:
> > On Thu, 2019-04-18 at 22:53 +0200, Martin Blumenstingl wrote:
> > > Hi Jerome,
> > >
> > > On Thu, Apr 18, 2019 at 10:46 PM Jerome Brunet <jbrunet@baylibre.com> wrote:
> > > > On Thu, 2019-04-18 at 22:16 +0200, Martin Blumenstingl wrote:
> > > > > Hi Jerome,
> > > > >
> > > > > On Wed, Apr 17, 2019 at 10:44 PM Jerome Brunet <jbrunet@baylibre.com> wrote:
> > > > > > Activating DDR in the Amlogic mmc controller, among other things, will
> > > > > > divide the output clock by 2. So by activating it with clock on, we are
> > > > > > creating a glitch on the output.
> > > > > >
> > > > > > Instead, let's deal with DDR when the clock output is off, when setting
> > > > > > the clock.
> > > > > >
> > > > > > Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
> > > > > it seems that this patch breaks SD card on my Khadas VIM and Khadas VIM2.
> > > >
> > > > The error I see in your logs is with eMMC and hs200, not SD card.
> > > sorry, I should have been more clear that there are two errors:
> > > eMMC, this is what I have been seeing for a while on my Khadas VIM2
> > > (it's probably not related to this patch):
> > > mmc1: mmc_select_hs200 failed, error -84
> > > mmc1: error -84 whilst initialising MMC card
> >
> > Following patches were also supposed to help the vim2.
> > ... something I tested numerous time on this particular board.
> >
> > > however, then there's this other error:
> > > print_req_error: I/O error, dev mmcblk0, sector 0 flags 0
> > > Buffer I/O error on dev mmcblk0, logical block 0, async page read
> > > as result of this the partition table cannot be read and my kernel
> > > cannot find the rootfs.
> >
> > I don't know what the problem is (probably some CRC error - you can check the log
> > in interrupt for this) but I'm pretty sure it is not related to this patch.
> >
> > I see in the log SD is indeed in HS mode, so not in any DDR mode.
> > I also see that the SDIO fails as well. There something really weird, which can't
> > be explained by this patch alone AFAICT.
>
> Ok, I think I got it. It is indeed not linked to DDR, but a more trivial mistake.
> It looks like a writel went AWOL during the final rebase (and after the test campaign).
>
> in meson_mmc_set_ios, after:
> val |= FIELD_PREP(CFG_BUS_WIDTH_MASK, bus_width);
>
> Could you try adding
> writel(val, host->regs + SD_EMMC_CFG);
good catch!

> Without this, the bus width is not changed, which explains why eMMC, SD and SDIO fail
> on init.
I have added that missing writel on top of the whole series and now:
- SD card is detected again (same as without this series)
- SDIO wifi is detected again (same as without this series)
- eMMC is detected (was not working before)

I will give my Tested-by on v2 of these patches


Martin

\
 
 \ /
  Last update: 2019-04-20 11:24    [W:0.059 / U:1.276 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site