lkml.org 
[lkml]   [2019]   [Apr]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH v5 1/3] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
Date
From
Hi Rob,


On 2019-04-18 08:13, Rob Herring wrote:
> On Wed, Apr 17, 2019 at 09:55:12AM -0700, Angus Ainslie (Purism) wrote:
>> This is the development kit board for the Librem 5. The current level
>> of
>> support yields a working console and is able to boot userspace from
>> the
>> Network or eMMC.
>>
>> Additional subsystems that are active :
>>
>> - Both USB ports
>> - SD card socket
>> - WiFi usdhc
>> - WWAN modem
>> - GNSS
>> - GPIO keys
>> - LEDs
>> - gyro
>> - magnetometer
>> - touchscreen
>> - pwm
>> - backlight
>> - haptic motor
>>
>> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
>> ---
>> arch/arm64/boot/dts/freescale/Makefile | 1 +
>> .../dts/freescale/imx8mq-librem5-devkit.dts | 833
>> ++++++++++++++++++
>> 2 files changed, 834 insertions(+)
>> create mode 100644
>> arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
>>
>> diff --git a/arch/arm64/boot/dts/freescale/Makefile
>> b/arch/arm64/boot/dts/freescale/Makefile
>> index 0bd122f60549..c043aca66572 100644
>> --- a/arch/arm64/boot/dts/freescale/Makefile
>> +++ b/arch/arm64/boot/dts/freescale/Makefile
>> @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
>>
>> dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
>> dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
>> +dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
>> dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
>> dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
>> dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
>> b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
>> new file mode 100644
>> index 000000000000..846a72dc7640
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
>
>> +&usb3_phy0 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "okay";
>> +
>> + port@0 {
>> + reg = <0>;
>> +
>> + typec_hs: endpoint {
>> + remote-endpoint = <&usb_con_hs>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + typec_ss: endpoint {
>> + remote-endpoint = <&usb_con_ss>;
>> + };
>> + };
>
> This is wrong. The graph should be between the USB controller and the
> connector. The phy is not involved.
>
>> +};
>> +
>> +&usb3_phy1 {
>> + status = "okay";
>> +};
>> +
>> +&usb_dwc3_0 {
>> + extcon = <&typec_ptn5100>;
>
> extcon is deprecated and you should only have the usb-connector
> binding.
> From the controller, you can walk the graph to the connector.
>

I not sure that I'm clear on what you mean. Here's what I think you want
it changed to.

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index 846a72dc7640..7b8770fdc5fb 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -755,51 +755,50 @@
};

&uart4 { /* BT */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>, <&pinctrl_bt>;
uart-has-rtscts;
status = "okay";
};

&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+&usb_dwc3_0 {
#address-cells = <1>;
#size-cells = <0>;
+ dr_mode = "otg";
status = "okay";

port@0 {
reg = <0>;

typec_hs: endpoint {
remote-endpoint = <&usb_con_hs>;
};
};

port@1 {
reg = <1>;

typec_ss: endpoint {
remote-endpoint = <&usb_con_ss>;
};
};
};

-&usb3_phy1 {
- status = "okay";
-};
-
-&usb_dwc3_0 {
- extcon = <&typec_ptn5100>;
- dr_mode = "otg";
- status = "okay";
-};
-
&usb_dwc3_1 {
dr_mode = "host";
status = "okay";
};



Thanks
Angus

>> + dr_mode = "otg";
>> + status = "okay";
>> +};

\
 
 \ /
  Last update: 2019-04-18 19:45    [W:0.064 / U:0.800 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site