lkml.org 
[lkml]   [2019]   [Apr]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/4] hwmon: (pmbus) add support for IR35215
On Tue, Apr 16, 2019 at 11:36:18AM -0700, Ruslan Babayev wrote:
> Provide support for Infineon Dual Output Digital Multi-Phase Buck
> Controllers IR35215 and IR3570B.
>
> Cc: xe-linux-external@cisco.com
> Signed-off-by: Ruslan Babayev <ruslan@babayev.com>
> ---
> Documentation/hwmon/ir35215 | 98 +++++++++++++++++++++++++++++++++++
> drivers/hwmon/pmbus/Kconfig | 10 ++++
> drivers/hwmon/pmbus/Makefile | 1 +
> drivers/hwmon/pmbus/ir35215.c | 91 ++++++++++++++++++++++++++++++++
> 4 files changed, 200 insertions(+)
> create mode 100644 Documentation/hwmon/ir35215
> create mode 100644 drivers/hwmon/pmbus/ir35215.c
>
> diff --git a/Documentation/hwmon/ir35215 b/Documentation/hwmon/ir35215
> new file mode 100644
> index 000000000000..b77481340006
> --- /dev/null
> +++ b/Documentation/hwmon/ir35215
> @@ -0,0 +1,98 @@
> +Kernel driver ir35215
> +=====================
> +
> +Supported chips:
> + * Infinion IR35215
> + Prefix: 'ir35215'
> + Addresses scanned: -
> + Datasheet: Datasheet is not publicly available.
> + * Infinion IR3570B
> + Prefix: 'ir3570b'
> + Addresses scanned: -
> + Datasheet: Datasheet is not publicly available.
> +
> +Author: Ruslan Babayev <ruslan@babayev.com>
> +
> +
> +Description
> +-----------
> +
> +IR35215 is a Dual Output Digital Multi-Phase Controller
> +
> +
> +Usage Notes
> +-----------
> +
> +This driver does not probe for PMBus devices. You will have to instantiate
> +devices explicitly.
> +
> +Example: the following commands will load the driver for an IR35215
> +at address 0x40 on I2C bus #4:
> +
> +# modprobe ir35215
> +# echo ir35215 0x40 > /sys/bus/i2c/devices/i2c-4/new_device
> +
> +
> +Sysfs attributes
> +----------------
> +
> +curr[1-2]_label "iin[1-2]"
> +curr[1-2]_input Measured input current
> +curr[1-2]_max Maximum current for
> +curr[1-2]_max_alarm Current high alarm
> +
> +curr[3-4]_label "iout[3-4]"
> +curr[3-4]_input Measured output current
> +curr[3-4]_crit Critical maximum current
> +curr[3-4]_crit_alarm Current critical high alarm
> +curr[3-4]_highest Highest output current
> +curr[3-4]_lowest Lowest output current
> +curr[3-4]_max Maximum current
> +curr[3-4]_max_alarm Current high alarm
> +
> +in[1-2]_label "vin[1-2]"
> +in[1-2]_input Measured input voltage
> +in[1-2]_crit Critical maximum input voltage
> +in[1-2]_crit_alarm Input voltage critical high alarm
> +in[1-2]_highest Highest input voltage
> +in[1-2]_lowest Lowest input voltage
> +in[1-2]_min Minimum input voltage
> +in[1-2]_min_alarm Input voltage low alarm
> +
> +in[3-4]_label "vout[3-4]"
> +in[3-4]_input Measured output voltage
> +in[3-4]_lcrit Critical minimum output voltage
> +in[3-4]_lcrit_alarm Output voltage critical low alarm
> +in[3-4]_crit Critical maximum output voltage
> +in[3-4]_crit_alarm Output voltage critical high alarm
> +in[3-4]_highest Highest output voltage
> +in[3-4]_lowest Lowest output voltage
> +in[3-4]_max Maximum output voltage
> +in[3-4]_max_alarm Output voltage high alarm
> +in[3-4]_min Minimum output voltage
> +in[3-4]_min_alarm Output voltage low alarm
> +
> +out[1-2]_command Commanded output voltage
> +out[1-2]_margin_high Output voltage when operation is set to "high"
> +out[1-2]_margin_low Output voltage when operation is set to "low"
> +out[1-2]_max Maximum output voltage
> +out[1-2]_max_alarm Output voltage high alarm
> +out[1-2]_operation Set the output voltage to "on", "off", "high" or "low"
> +
> +power1_label "pin"
> +power1_input Measured input power
> +power1_alarm Input power high alarm
> +power1_max Input power limit
> +
> +power[2-3]_label "pout[1-2]"
> +power[2-3]_input Measured output power
> +power[2-3]_max Output power limit
> +power[2-3]_max_alarm Output power high alarm
> +
> +temp[1-2]_input Measured temperature
> +temp[1-2]_crit Critical high temperature
> +temp[1-2]_crit_alarm Chip temperature critical high alarm
> +temp[1-2]_highest Highest temperature
> +temp[1-2]_lowest Lowest temperature
> +temp[1-2]_max Maximum temperature
> +temp[1-2]_max_alarm Chip temperature high alarm
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index 629cb45f8557..a7dd5e606061 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -45,6 +45,16 @@ config SENSORS_IBM_CFFPS
> This driver can also be built as a module. If so, the module will
> be called ibm-cffps.
>
> +config SENSORS_IR35215
> + tristate "Infineon IR35215"
> + default n
> + help
> + If you say yes here you get hardware monitoring support for the
> + Infineon IR35215 controller.
> +
> + This driver can also be built as a module. If so, the module will
> + be called ir35215.
> +
> config SENSORS_IR35221
> tristate "Infineon IR35221"
> help
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index ea0e39518c21..48643e3bab42 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -7,6 +7,7 @@ obj-$(CONFIG_PMBUS) += pmbus_core.o
> obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
> obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
> obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
> +obj-$(CONFIG_SENSORS_IR35215) += ir35215.o
> obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
> obj-$(CONFIG_SENSORS_LM25066) += lm25066.o
> obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o
> diff --git a/drivers/hwmon/pmbus/ir35215.c b/drivers/hwmon/pmbus/ir35215.c
> new file mode 100644
> index 000000000000..e50ee465a42d
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/ir35215.c
> @@ -0,0 +1,91 @@
> +/*
> + * Hardware monitoring driver for Infineon IR35215
> + *
> + * Copyright (c) 2019 Cisco Systems.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/init.h>
> +#include <linux/err.h>
> +#include <linux/i2c.h>

Alphabetic include file order please.

> +#include "pmbus.h"
> +
> +#define COMMON_FUNCS (PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT \
> + | PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT \
> + | PMBUS_HAVE_PIN | PMBUS_HAVE_POUT \
> + | PMBUS_HAVE_TEMP \
> + | PMBUS_HAVE_STATUS_VOUT \
> + | PMBUS_HAVE_STATUS_IOUT \
> + | PMBUS_HAVE_STATUS_INPUT \
> + | PMBUS_HAVE_STATUS_TEMP \
> + | PMBUS_HAVE_VOUT_MARGIN_HIGH \
> + | PMBUS_HAVE_VOUT_MARGIN_LOW \
> + )
> +
> +
> +#define IR35215_FUNCS (COMMON_FUNCS | PMBUS_HAVE_VOUT_COMMAND)
> +#define IR3570B_FUNCS (COMMON_FUNCS | PMBUS_HAVE_TEMP2)
> +
> +static struct pmbus_driver_info ir35215_info = {
> + .pages = 2,
> + .format[PSC_VOLTAGE_IN] = linear,
> + .format[PSC_VOLTAGE_OUT] = linear,
> + .format[PSC_CURRENT_IN] = linear,
> + .format[PSC_CURRENT_OUT] = linear,
> + .format[PSC_POWER] = linear,
> + .format[PSC_TEMPERATURE] = linear,
> + .func[0] = IR35215_FUNCS,
> + .func[1] = IR35215_FUNCS,
> +};
> +
> +static struct pmbus_driver_info ir3570b_info = {
> + .pages = 1,

Either this ...

> + .format[PSC_VOLTAGE_IN] = linear,
> + .format[PSC_VOLTAGE_OUT] = linear,
> + .format[PSC_CURRENT_IN] = linear,
> + .format[PSC_CURRENT_OUT] = linear,
> + .format[PSC_POWER] = linear,
> + .format[PSC_TEMPERATURE] = linear,
> + .func[0] = IR3570B_FUNCS,
> + .func[1] = IR3570B_FUNCS,

... or this is wrong.

> +};
> +
> +static int ir35215_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + return pmbus_do_probe(client, id, (void *)id->driver_data);
> +}
> +
> +static const struct i2c_device_id ir35215_id[] = {
> + {"ir35215", (kernel_ulong_t)&ir35215_info},
> + {"ir3570b", (kernel_ulong_t)&ir3570b_info},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, ir35215_id);
> +
> +static struct i2c_driver ir35215_driver = {
> + .driver = {
> + .name = "ir35215",
> + },
> + .probe = ir35215_probe,
> + .remove = pmbus_do_remove,
> + .id_table = ir35215_id,
> +};
> +
> +module_i2c_driver(ir35215_driver);
> +
> +MODULE_AUTHOR("Ruslan Babayev <ruslan@babayev.com>");
> +MODULE_DESCRIPTION("PMBus driver for IR35215");
> +MODULE_LICENSE("GPL");
> --
> 2.17.1
>

\
 
 \ /
  Last update: 2019-04-16 22:17    [W:0.040 / U:2.472 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site