lkml.org 
[lkml]   [2019]   [Apr]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/2] regulator: Add support for stm32 power regulators
Date
Add support for 1V1 1V8 USB3V3 power regulators.

Signed-off-by: Pascal Paillet <p.paillet@st.com>
---
drivers/regulator/Kconfig | 7 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/stm32-pwr.c | 190 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 198 insertions(+)
create mode 100644 drivers/regulator/stm32-pwr.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index c4dc2bc..6c37f0d 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -840,6 +840,13 @@ config REGULATOR_STM32_VREFBUF
This driver can also be built as a module. If so, the module
will be called stm32-vrefbuf.

+config REGULATOR_STM32_PWR
+ bool "STMicroelectronics STM32 PWR"
+ depends on ARCH_STM32 || COMPILE_TEST
+ help
+ This driver supports internal regulators (1V1, 1V8, 3V3) in the
+ STMicroelectronics STM32 chips.
+
config REGULATOR_STPMIC1
tristate "STMicroelectronics STPMIC1 PMIC Regulators"
depends on MFD_STPMIC1
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 1169f8a..93f5384 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -105,6 +105,7 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
+obj-$(CONFIG_REGULATOR_STM32_PWR) += stm32-pwr.o
obj-$(CONFIG_REGULATOR_STPMIC1) += stpmic1_regulator.o
obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
obj-$(CONFIG_REGULATOR_SY8106A) += sy8106a-regulator.o
diff --git a/drivers/regulator/stm32-pwr.c b/drivers/regulator/stm32-pwr.c
new file mode 100644
index 0000000..e434b26
--- /dev/null
+++ b/drivers/regulator/stm32-pwr.c
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) STMicroelectronics 2019
+// Authors: Gabriel Fernandez <gabriel.fernandez@st.com>
+// Pascal Paillet <p.paillet@st.com>.
+
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+/*
+ * Registers description
+ */
+#define REG_PWR_CR3 0x0C
+
+#define USB_3_3_EN BIT(24)
+#define USB_3_3_RDY BIT(26)
+#define REG_1_8_EN BIT(28)
+#define REG_1_8_RDY BIT(29)
+#define REG_1_1_EN BIT(30)
+#define REG_1_1_RDY BIT(31)
+
+/* list of supported regulators */
+enum {
+ PWR_REG11,
+ PWR_REG18,
+ PWR_USB33,
+ STM32PWR_REG_NUM_REGS
+};
+
+u32 ready_mask_table[STM32PWR_REG_NUM_REGS] = {
+ [PWR_REG11] = REG_1_1_RDY,
+ [PWR_REG18] = REG_1_8_RDY,
+ [PWR_USB33] = USB_3_3_RDY,
+};
+
+struct stm32_pwr_reg {
+ void __iomem *base;
+ const struct regulator_desc *desc;
+ u32 ready_mask;
+};
+
+int stm32_pwr_reg_is_ready(struct regulator_dev *rdev)
+{
+ struct stm32_pwr_reg *priv = rdev_get_drvdata(rdev);
+ u32 val;
+
+ val = readl_relaxed(priv->base + REG_PWR_CR3);
+
+ return (val & priv->ready_mask);
+}
+
+int stm32_pwr_reg_is_enabled(struct regulator_dev *rdev)
+{
+ struct stm32_pwr_reg *priv = rdev_get_drvdata(rdev);
+ u32 val;
+
+ val = readl_relaxed(priv->base + REG_PWR_CR3);
+
+ return (val & priv->desc->enable_mask);
+}
+
+static int stm32_pwr_reg_enable(struct regulator_dev *rdev)
+{
+ struct stm32_pwr_reg *priv = rdev_get_drvdata(rdev);
+ int ret;
+ u32 val;
+
+ val = readl_relaxed(priv->base + REG_PWR_CR3);
+ val |= priv->desc->enable_mask;
+ writel_relaxed(val, priv->base + REG_PWR_CR3);
+
+ /* use an arbitrary timeout of 20ms */
+ ret = readx_poll_timeout(stm32_pwr_reg_is_ready, rdev, val, val,
+ 100, 20 * 1000);
+ if (ret)
+ dev_err(&rdev->dev, "regulator enable timed out!\n");
+
+ return ret;
+}
+
+static int stm32_pwr_reg_disable(struct regulator_dev *rdev)
+{
+ struct stm32_pwr_reg *priv = rdev_get_drvdata(rdev);
+ int ret;
+ u32 val;
+
+ val = readl_relaxed(priv->base + REG_PWR_CR3);
+ val &= ~priv->desc->enable_mask;
+ writel_relaxed(val, priv->base + REG_PWR_CR3);
+
+ /* use an arbitrary timeout of 20ms */
+ ret = readx_poll_timeout(stm32_pwr_reg_is_ready, rdev, val, !val,
+ 100, 20 * 1000);
+ if (ret)
+ dev_err(&rdev->dev, "regulator disable timed out!\n");
+
+ return ret;
+}
+
+static const struct regulator_ops stm32_pwr_reg_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .enable = stm32_pwr_reg_enable,
+ .disable = stm32_pwr_reg_disable,
+ .is_enabled = stm32_pwr_reg_is_enabled,
+};
+
+#define PWR_REG(_id, _name, _volt, _en, _supply) \
+ [_id] = { \
+ .id = _id, \
+ .name = _name, \
+ .of_match = of_match_ptr(_name), \
+ .n_voltages = 1, \
+ .type = REGULATOR_VOLTAGE, \
+ .min_uV = _volt, \
+ .fixed_uV = _volt, \
+ .ops = &stm32_pwr_reg_ops, \
+ .enable_mask = _en, \
+ .owner = THIS_MODULE, \
+ .supply_name = _supply, \
+ } \
+
+static const struct regulator_desc stm32_pwr_desc[] = {
+ PWR_REG(PWR_REG11, "reg11", 1100000, REG_1_1_EN, "vdd"),
+ PWR_REG(PWR_REG18, "reg18", 1800000, REG_1_8_EN, "vdd"),
+ PWR_REG(PWR_USB33, "usb33", 3300000, USB_3_3_EN, "vdd_3v3_usbfs"),
+};
+
+static int stm32_pwr_regulator_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct stm32_pwr_reg *priv;
+ void __iomem *base;
+ struct regulator_dev *rdev;
+ struct regulator_config config = { };
+ int i, ret = 0;
+
+ base = of_iomap(np, 0);
+ if (IS_ERR(base)) {
+ dev_err(&pdev->dev, "Unable to map IO memory\n");
+ return PTR_ERR(base);
+ }
+
+ config.dev = &pdev->dev;
+
+ for (i = 0; i < STM32PWR_REG_NUM_REGS; i++) {
+ priv = devm_kzalloc(&pdev->dev, sizeof(struct stm32_pwr_reg),
+ GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+ priv->base = base;
+ priv->desc = &stm32_pwr_desc[i];
+ priv->ready_mask = ready_mask_table[i];
+ config.driver_data = priv;
+
+ rdev = devm_regulator_register(&pdev->dev,
+ &stm32_pwr_desc[i],
+ &config);
+ if (IS_ERR(rdev)) {
+ ret = PTR_ERR(rdev);
+ dev_err(&pdev->dev,
+ "Failed to register regulator: %d\n", ret);
+ break;
+ }
+ }
+ return ret;
+}
+
+static const struct of_device_id stm32_pwr_of_match[] = {
+ { .compatible = "st,stm32mp1,pwr-reg", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, stm32_pwr_of_match);
+
+static struct platform_driver stm32_pwr_driver = {
+ .probe = stm32_pwr_regulator_probe,
+ .driver = {
+ .name = "stm32-pwr-regulator",
+ .of_match_table = of_match_ptr(stm32_pwr_of_match),
+ },
+};
+module_platform_driver(stm32_pwr_driver);
+
+MODULE_DESCRIPTION("STM32MP1 PWR voltage regulator driver");
+MODULE_AUTHOR("Pascal Paillet <p.paillet@st.com>");
+MODULE_LICENSE("GPL v2");
--
1.9.1
\
 
 \ /
  Last update: 2019-04-15 11:19    [W:0.037 / U:6.844 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site