lkml.org 
[lkml]   [2019]   [Apr]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] ARM: dts: sun8i: v40: Update BPi M2 Berry DTS to the level of M2 Ultra
Date
From: Pablo Greco <pgreco@centosproject.org>

BPi M2 Berry is a trimmed down version of the BPi M2 Ultra, completely
software compatible.

Changes include:
- 2GiB -> 1GiB
- no eMMC
- no onboard microphone
- no IR
- no blue LED
- no charging (and power jack to USB)
- dropped USB2 and connect USB1 to a 4-port HUB.

This patch brings the BPi M2 Berry to the same level as the BPi M2 Ultra
Includes the changes from:
commit c36fd5a48bd2 ("ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable GMAC
ethernet controller")
commit db49c6825901 ("ARM: dts: sun8i: r40: Enable HDMI output on BananaPi
M2 Ultra")
commit ccefd95f648a ("ARM: dts: sun8i: r40: Add missing TCON-TOP - TCON
connections")
commit 6a7556f604f9 ("ARM: dts: sun8i: r40: Disable TCONs by default.")
commit 666907a3f9bd ("ARM: dts: sun8i: sun8i-r40-bananapi-m2-ultra: enable
AHCI")
commit e5c6e693be83 ("ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix WiFi
regulator definitions")
commit 1e5f1db4ccd8 ("ARM: dts: sun8i: r40: bananapi-m2-ultra: Add
Bluetooth device node")

Signed-off-by: Pablo Greco <pgreco@centosproject.org>
---
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 118 ++++++++++++++++++++++
1 file changed, 118 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index f05cabd..3d0bb7e 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -50,6 +50,7 @@
compatible = "sinovoip,bpi-m2-berry", "allwinner,sun8i-r40";

aliases {
+ ethernet0 = &gmac;
serial0 = &uart0;
};

@@ -57,6 +58,17 @@
stdout-path = "serial0:115200n8";
};

+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";

@@ -84,14 +96,52 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+ clocks = <&ccu CLK_OUTA>;
+ clock-names = "ext_clock";
};
};

+&ahci {
+ ahci-supply = <&reg_dldo4>;
+ phy-supply = <&reg_eldo3>;
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
&ehci1 {
/* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
status = "okay";
};

+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_rgmii_pins>;
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <&reg_dc1sw>;
+ status = "okay";
+};
+
+&gmac_mdio {
+ phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
status = "okay";

@@ -123,6 +173,18 @@
status = "okay";
};

+&pio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&clk_out_a_pin>;
+};
+
+&reg_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa";
+};
+
&reg_aldo3 {
regulator-always-on;
regulator-min-microvolt = <2700000>;
@@ -130,6 +192,12 @@
regulator-name = "avcc";
};

+&reg_dc1sw {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-gmac-phy";
+};
+
&reg_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
@@ -164,18 +232,68 @@
regulator-name = "vcc-wifi-io";
};

+/*
+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same
+ * time, with the two being in sync, to be able to meet maximum power
+ * consumption during transmits. Since this is not really supported
+ * right now, just use the two as always on, and we will fix it later.
+ */
+
&reg_dldo2 {
+ regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};

+&reg_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+};
+
+&reg_dldo4 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vdd2v5-sata";
+};
+
+&reg_eldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd1v2-sata";
+};
+
+&tcon_tv0 {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};

+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&ccu CLK_OUTA>;
+ clock-names = "lpo";
+ vbat-supply = <&reg_dldo2>;
+ vddio-supply = <&reg_dldo1>;
+ device-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+ /* TODO host wake line connected to PMIC GPIO pins */
+ shutdown-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
+ max-speed = <1500000>;
+ };
+};
+
&usbphy {
usb1_vbus-supply = <&reg_vcc5v0>;
status = "okay";
--
1.8.3.1
\
 
 \ /
  Last update: 2019-04-11 14:02    [W:1.256 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site