lkml.org 
[lkml]   [2019]   [Apr]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
SubjectRe: [PATCH v1 1/2] dt-bindings: mmc: sdhci-fujitsu.txt: add miilbeaut driver
Date

Hi

> On Tue, Mar 26, 2019 at 02:53:37PM +0900, Takao Orito wrote:
> > Add new compatible description for Milbeaut SoC. Socionext
> > inherits F_SDH30 IP from Fujitsu. Then new Soc series "Milbeaut"
> > has F_SDH30 controller specified by "socionext,milbeaut-m10v-sdhci-3.0".
>
> Subject is wrong, you're not adding a driver.

OK, I will change "dt-bindings: mmc: sdhci-fujitsu.txt: add milbeaut support"

>
> >
> > Signed-off-by: Takao Orito <orito.takao@socionext.com>
> > ---
> > .../devicetree/bindings/mmc/sdhci-fujitsu.txt | 22 +++++++++++++++++++---
> > 1 file changed, 19 insertions(+), 3 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> > index 3ee9263..405811f 100644
> > --- a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> > +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> > @@ -1,10 +1,10 @@
> > -* Fujitsu SDHCI controller
> > +* Fujitsu/Socionext SDHCI controller
> >
> > This file documents differences between the core properties in mmc.txt
> > -and the properties used by the sdhci_f_sdh30 driver.
> > +and the properties used by the sdhci_f_sdh30.
> >
> > Required properties:
> > -- compatible: "fujitsu,mb86s70-sdhci-3.0"
> > +- compatible: "fujitsu,mb86s70-sdhci-3.0", "socionext,milbeaut-m10v-sdhci-3.0"
>
> One per line please.

I see, I will fix.

>
> > - clocks: Must contain an entry for each entry in clock-names. It is a
> > list of phandles and clock-specifier pairs.
> > See ../clocks/clock-bindings.txt for details.
> > @@ -17,6 +17,8 @@ Optional properties:
> > as the VCCQ/VDD_IO supply in the eMMC/SD specs.
> > - fujitsu,cmd-dat-delay-select: boolean property indicating that this host
> > requires the CMD_DAT_DELAY control to be enabled.
> > +- sni,mmc-power-gpio: set property indicating that power on or off needs
> > + control of gpio. This is for only "socionext,milbeaut-m10v-sdhci-3.0".
>
> s/-gpio/-gpios/

I will fix.

>
> >
> > Example:
> >
> > @@ -30,3 +32,17 @@ Example:
> > clocks = <&clock 2 2 0>, <&clock 2 3 0>;
> > clock-names = "iface", "core";
> > };
> > +
> > +Exsample2:
> > + sdhci3: mmc@1b010000 {
> > + compatible = "socionext,milbeaut-m10v-sdhci-3.0";
> > + reg = <0x1b010000 0x10000>;
> > + interrupts = <0 265 0x4>;
> > + voltage-ranges = <3300 3300>;
> > + bus-width = <4>;
> > + clocks = <&uhs1clk2>, <&ahb_clk>;
> > + clock-names = "core", "iface";
> > + cap-sdio-irq;
> > + sni,mmc-power-gpio = <&pinctrl 53 GPIO_ACTIVE_HIGH>;
> > + fujitsu,cmd-dat-delay-select;
>
> Indentation problem.

Sorry, I will fix.

Thank you
Orito

>
> > + };
> > --
> > 1.9.1
> >
> >

--
Takao Orito <orito.takao@socionext.com>
\
 
 \ /
  Last update: 2019-04-02 04:06    [W:0.320 / U:7.072 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site