lkml.org 
[lkml]   [2019]   [Apr]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/7] dt-bindings: mfd: Document Macronix MX25F0A controller bindings
Hi Mason,

Mason Yang <masonccyang@mxic.com.tw> wrote on Thu, 28 Mar 2019 18:18:35
+0800:

> Document the bindings used by the Macronix MX25F0A MFD controller.
>
> Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
> ---
> .../devicetree/bindings/mfd/mxic-mx25f0a.txt | 66 ++++++++++++++++++++++
> 1 file changed, 66 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/mxic-mx25f0a.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/mxic-mx25f0a.txt b/Documentation/devicetree/bindings/mfd/mxic-mx25f0a.txt
> new file mode 100644
> index 0000000..53b4839
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/mxic-mx25f0a.txt
> @@ -0,0 +1,66 @@
> +Macronix MX25F0A Multi-Function Device Tree Bindings
> +----------------------------------------------------
> +
> +MX25F0A is a MultiFunction Device with SPI and raw NAND, which
> +supports either spi host controller or raw nand controller.
> +
> +Required properties:
> +- compatible: should be "mxic,mx25f0a-mfd"

Should probably be "mxic,mx25f0a"

> +- #address-cells: should be 1
> +- #size-cells: should be 0
> +- reg: should contain 2 entries, one for the registers and one for the direct
> + mapping area in SPI mode.
> +- reg-names: should contain "regs" and "dirmap"
> +- interrupts: interrupt line connected to this MFD controller
> +
> +Required nodes:
> + - spi :
> + Node for configuring the SPI controller driver.
> + Required properties:
> + - compatible = "mxicy,mx25f0a-spi";
> + - clock-names: should contain "ps_clk", "send_clk" and
> + "send_dly_clk"
> + - clocks: should contain 3 entries for the "ps_clk", "send_clk"
> + and "send_dly_clk" clocks
> +
> +- nand :
> + Node for configuring the raw nand controller driver.
> + Required properties:
> + - compatible = "mxicy,mx25f0a-nand-ctlr";
> + - nand-ecc-mode = "soft";
> + - nand-ecc-algo = "bch";

You can have only one node at a time. You can add a mxic,mode property
being either "spi-controller" or "nand-controller".

> +
> +Example:
> +
> + mxic: mx25f0a-mfd@43c30000 {
> + compatible = "mxic,mx25f0a-mfd";
> + reg = <0x43c30000 0x10000>, <0xa0000000 0x4000000>;
> + reg-names = "regs", "dirmap";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* either spi or nand */
> + spi {
> + compatible = "mxicy,mx25f0a-spi";
> + clocks = <&clkwizard 0>, <&clkwizard 1>, <&clkc 15>;
> + clock-names = "send_clk", "send_dly_clk", "ps_clk";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + };
> + };
> +
> + nand {
> + compatible = "mxicy,mx25f0a-nand-ctlr";
> + nand-ecc-mode = "soft";
> + nand-ecc-algo = "bch";
> + nand-ecc-step-size = <512>;
> + nand-ecc-strength = <8>;

Are you sure you want soft correction? (I have not checked the driver
yet). For hw correction, I prefer to drop the two step-size/strength
properties. These values will be derived depending on the chip's
requirements.


Thanks,
Miquèl

\
 
 \ /
  Last update: 2019-04-01 19:54    [W:0.071 / U:0.972 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site