lkml.org 
[lkml]   [2019]   [Mar]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2] tty/serial: Add a serial port simulator
From
Date
On 3/5/19 5:51 PM, Corey Minyard wrote:
> On Tue, Mar 05, 2019 at 03:29:51PM -0800, Randy Dunlap wrote:
>> Hi Corey,
>>
>> Just some doc comments.
>
> Thanks a bunch. A few comments inline on things I didn't do quite
> like you suggested..
>
>>
>> On 3/5/19 9:12 AM, minyard@acm.org wrote:
>>> diff --git a/Documentation/serial/serialsim.rst b/Documentation/serial/serialsim.rst
>>> new file mode 100644
>>> index 000000000000..655e10b4908e
>>> --- /dev/null
>>> +++ b/Documentation/serial/serialsim.rst
>>> @@ -0,0 +1,149 @@
>>> +.. SPDX-License-Identifier: GPL-2.0+
>>> +=====================================
>>> +serialsim - A kernel serial simualtor
>> xxxxxxxxx
>> serial device simulator
>>
>>> +=====================================
>>> +
>>> +:Author: Corey Minyard <minyard@mvista.com> / <minyard@acm.org>
>>> +
>>> +The serialsim device is a serial simulator with echo and pipe devices.
>>> +It is quite useful for testing programs that use serial ports.
>>> +
>>> +This attempts to emulate a basic serial device. It uses the baud rate
>>> +and sends the bytes through the loopback or pipe at approximately the
>>> +speed it would on a normal serial device.
>>> +
>>> +There is a python interface to the special ioctls for controlling the
>>> +remote end of the termios in addition to the standard ioctl interface
>>> +documented below. See https://github.com/cminyard/serialsim
>>> +
>>> +=====
>>> +Using
>>> +=====
>>> +
>>> +The serialsim.ko module creates two types of devices. Echo devices
>>> +simply echo back the data to the same device. These devices will
>>> +appear as /dev/ttyEcho<n>.
>>> +
>>> +Pipe devices will transfer the data between two devices. The
>>> +devices will appear as /dev/ttyPipeA<n> and /dev/ttyPipeB<n>. And
>>
>> Any
>>
>>> +data written to PipeA reads from PipeB, and vice-versa.
>>> +
>>> +You may create an arbitrary number of devices by setting the
>>> +nr_echo ports and nr_pipe_ports module parameters. The default is
>>
>> nr_echo_ports
>>
>>> +four for both.
>>
>> or for each.
>>
>>> +
>>> +This driver supports modifying the modem control lines and
>>> +injecting various serial errors. It also supports a simulated null
>>> +modem between the two pipes, or in a loopback on the echo device.
>>> +
>>> +By default a pipe or echo comes up in null modem configuration,
>>> +meaning that the DTR line is hooked to the DSR and CD lines on the
>>> +other side and the RTS line on one side is hooked to the CTS line
>>> +on the other side.
>>> +
>>> +The RTS and CTS lines don't currently do anything for flow control.
>>> +
>>> +You can modify null modem and control the lines individually
>>> +through an interface in /sys/class/tty/ttyECHO<n>/ctrl,
>>> +/sys/class/tty/ttyPipeA<n>/ctrl, and
>>> +/sys/class/tty/ttyPipeB<n>/ctrl. The following may be written to
>>> +those files:
>>> +
>>> +[+-]nullmodem
>>> + enable/disable null modem
>>> +
>>> +[+-]cd
>>> + enable/disable Carrier Detect (no effect if +nullmodem)
>>> +
>>> +[+-]dsr
>>> + enable/disable Data Set Ready (no effect if +nullmodem)
>>> +
>>> +[+-]cts
>>> + enable/disable Clear To Send (no effect if +nullmodem)
>>> +
>>> +[+-]ring
>>> + enable/disable Ring
>>> +
>>> +frame
>>> + inject a frame error on the next byte
>>> +
>>> +parity
>>> + inject a parity error on the next byte
>>> +
>>> +overrun
>>> + inject an overrun error on the next byte
>>> +
>>> +The contents of the above files has the following format:
>>
>> have
>
> This intrigued me a bit. I assumed, even though "contents" can
> be plural, it is used in a singular fashion here because it is one
> "thing". So I did some research. I couldn't really find
> anything definitive, and there seems to be a lot of debate on
> this. But if you look at:
> https://dictionary.cambridge.org/grammar/british-grammar/content-or-contents
> you will see, when they use "contents", they use a singular verb
> with it:
> The contents of a book is the list of chapters or articles...
> So if it's good enough for Cambridge, it's good enough for me :).
> Though I'm certainly no grammar expert.

OK :)

>>
>>> +
>>> +tty[Echo|PipeA|PipeB]<n>
>>> + <mctrl values>
>>> +
>>> +where <mctrl values> is the modem control values above (not frame,
>>> +parity, or overrun) with the following added:
>>> +
>>> +[+-]dtr
>>> + value of the Data Terminal Ready
>>> +
>>> +[+-]rts
>>> + value of the Request To Send
>>> +
>>> +The above values are not settable through this interface, they are
>>> +set through the serial port interface itself.
>>> +
>>> +So, for instance, ttyEcho0 comes up in the following state::
>>> +
>>> + # cat /sys/class/tty/ttyEcho0/ctrl
>>> + ttyEcho0: +nullmodem -cd -dsr -cts -ring -dtr -rts
>>> +
>>> +If something connects, it will become::
>>> +
>>> + ttyEcho0: +nullmodem +cd +dsr +cts -ring +dtr +rts
>>> +
>>> +To enable ring::
>>> +
>>> + # echo "+ring" >/sys/class/tty/ttyEcho0/ctrl
>>> + # cat /sys/class/tty/ttyEcho0/ctrl
>>> + ttyEcho0: +nullmodem +cd +dsr +cts +ring +dtr +rts
>>> +
>>> +Now disable NULL modem and the CD line::
>>> +
>>> + # echo "-nullmodem -cd" >/sys/class/tty/ttyEcho0/ctrl
>>> + # cat /sys/class/tty/ttyEcho0/ctrl
>>> + ttyEcho0: -nullmodem -cd -dsr -cts +ring -dtr -rts
>>> +
>>> +Note that these settings are for the side you are modifying. So if
>>> +you set nullmodem on ttyPipeA0, that controls whether the DTR/RTS
>>> +lines from ttyPipeB0 affect ttyPipeA0. It doesn't affect ttyPipeB's
>>> +modem control lines.
>>> +
>>> +The PIPEA and PIPEB devices also have the ability to set these
>>> +values for the other end via an ioctl. The following ioctls are
>>> +available:
>>> +
>>> +TIOCSERSNULLMODEM
>>> + Set the null modem value, the arg is a boolean.
>>> +
>>> +TIOCSERSREMMCTRL
>>> + Set the modem control lines, bits 16-31 of the arg is
>>
>> are
>
> Same comment as above. IMHO, it's one set of bits.
>
>>
>>> + a 16-bit mask telling which values to set, bits 0-15 are the
>>> + actual values. Settable values are TIOCM_CAR, TIOCM_CTS,
>>> + TIOCM_DSR, and TIOC_RNG. If NULLMODEM is set to true, then only
>>> + TIOC_RNG is settable. The DTR and RTS lines are not here, you can
>>> + set them through the normal interface.
>>> +
>>> +TIOCSERSREMERR
>>> + Send an error or errors on the next sent byte. arg is
>>> + a bitwise OR of (1 << TTY_xxx). Allowed errors are TTY_BREAK,
>>
>> is this better: (or I don't understand?)
>> a bitwise OR of (1 << TTY_xxx) and one (or more of) the
>> allowed error flags TTY_BREAK, TTY_FRAME, TTY_PARITY, and TTY_OVERRUN.
>
> Well, not really. But what I wrote isn't great, so, how about:
>
> Send an error or errors on the next sent byte. arg is a bitwise
> OR of (1 << TTY_BREAK), (1 << TTY_FRAME), (1 << TTY_PARITY), and
> (1 << TTY_OVERRUN). If none of those are set, then no error
> is sent.

I see. Thanks.

> Thanks,
>
> -corey
>
>>
>>> + TTY_FRAME, TTY_PARITY, and TTY_OVERRUN.
>>> +
>>> +TIOCSERGREMTERMIOS
>>> + Return the termios structure for the other side of the pipe.
>>> + arg is a pointer to a standard termios struct.
>>> +
>>> +TIOCSERGREMRS485
>>> + Return the remote RS485 settings, arg is a pointer to a struct
>>> + serial_rs485.
>>> +
>>> +Note that unlike the sysfs interface, these ioctls affect the other
>>> +end. So setting nullmodem on the ttyPipeB0 interface sets whether
>>> +the DTR/RTS lines on ttyPipeB0 affect ttyPipeA0.
>>
>>
>> cheers.
>> --
>> ~Randy


--
~Randy

\
 
 \ /
  Last update: 2019-03-06 03:05    [W:0.053 / U:1.068 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site