lkml.org 
[lkml]   [2019]   [Mar]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 24/28] userfaultfd: wp: UFFDIO_REGISTER_MODE_WP documentation update
On Wed, Mar 20, 2019 at 10:06:38AM +0800, Peter Xu wrote:
> From: Martin Cracauer <cracauer@cons.org>
>
> Adds documentation about the write protection support.
>
> Signed-off-by: Martin Cracauer <cracauer@cons.org>
> Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
> [peterx: rewrite in rst format; fixups here and there]
> Reviewed-by: Jerome Glisse <jglisse@redhat.com>
> Signed-off-by: Peter Xu <peterx@redhat.com>

Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>

> ---
> Documentation/admin-guide/mm/userfaultfd.rst | 51 ++++++++++++++++++++
> 1 file changed, 51 insertions(+)
>
> diff --git a/Documentation/admin-guide/mm/userfaultfd.rst b/Documentation/admin-guide/mm/userfaultfd.rst
> index 5048cf661a8a..c30176e67900 100644
> --- a/Documentation/admin-guide/mm/userfaultfd.rst
> +++ b/Documentation/admin-guide/mm/userfaultfd.rst
> @@ -108,6 +108,57 @@ UFFDIO_COPY. They're atomic as in guaranteeing that nothing can see an
> half copied page since it'll keep userfaulting until the copy has
> finished.
>
> +Notes:
> +
> +- If you requested UFFDIO_REGISTER_MODE_MISSING when registering then
> + you must provide some kind of page in your thread after reading from
> + the uffd. You must provide either UFFDIO_COPY or UFFDIO_ZEROPAGE.
> + The normal behavior of the OS automatically providing a zero page on
> + an annonymous mmaping is not in place.
> +
> +- None of the page-delivering ioctls default to the range that you
> + registered with. You must fill in all fields for the appropriate
> + ioctl struct including the range.
> +
> +- You get the address of the access that triggered the missing page
> + event out of a struct uffd_msg that you read in the thread from the
> + uffd. You can supply as many pages as you want with UFFDIO_COPY or
> + UFFDIO_ZEROPAGE. Keep in mind that unless you used DONTWAKE then
> + the first of any of those IOCTLs wakes up the faulting thread.
> +
> +- Be sure to test for all errors including (pollfd[0].revents &
> + POLLERR). This can happen, e.g. when ranges supplied were
> + incorrect.
> +
> +Write Protect Notifications
> +---------------------------
> +
> +This is equivalent to (but faster than) using mprotect and a SIGSEGV
> +signal handler.
> +
> +Firstly you need to register a range with UFFDIO_REGISTER_MODE_WP.
> +Instead of using mprotect(2) you use ioctl(uffd, UFFDIO_WRITEPROTECT,
> +struct *uffdio_writeprotect) while mode = UFFDIO_WRITEPROTECT_MODE_WP
> +in the struct passed in. The range does not default to and does not
> +have to be identical to the range you registered with. You can write
> +protect as many ranges as you like (inside the registered range).
> +Then, in the thread reading from uffd the struct will have
> +msg.arg.pagefault.flags & UFFD_PAGEFAULT_FLAG_WP set. Now you send
> +ioctl(uffd, UFFDIO_WRITEPROTECT, struct *uffdio_writeprotect) again
> +while pagefault.mode does not have UFFDIO_WRITEPROTECT_MODE_WP set.
> +This wakes up the thread which will continue to run with writes. This
> +allows you to do the bookkeeping about the write in the uffd reading
> +thread before the ioctl.
> +
> +If you registered with both UFFDIO_REGISTER_MODE_MISSING and
> +UFFDIO_REGISTER_MODE_WP then you need to think about the sequence in
> +which you supply a page and undo write protect. Note that there is a
> +difference between writes into a WP area and into a !WP area. The
> +former will have UFFD_PAGEFAULT_FLAG_WP set, the latter
> +UFFD_PAGEFAULT_FLAG_WRITE. The latter did not fail on protection but
> +you still need to supply a page when UFFDIO_REGISTER_MODE_MISSING was
> +used.
> +
> QEMU/KVM
> ========
>
> --
> 2.17.1
>

--
Sincerely yours,
Mike.

\
 
 \ /
  Last update: 2019-03-22 22:47    [W:0.189 / U:10.392 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site