lkml.org 
[lkml]   [2019]   [Mar]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v9 1/4] can: m_can: Create a m_can platform framework
From
Date
On 3/14/19 9:38 AM, Wolfgang Grandegger wrote:
> Hello,
>
> Am 14.03.19 um 15:04 schrieb Dan Murphy:
>> Hello
>>
>> On 3/14/19 2:26 AM, Wolfgang Grandegger wrote:
>>> Hello Dan,
>>>
>>> we are close...
>>>
>>> Am 13.03.19 um 17:26 schrieb Dan Murphy:
>>>> Create a m_can platform framework that peripherial
>>>> devices can register to and use common code and register sets.
>>>> The peripherial devices may provide read/write and configuration
>>>> support of the IP.
>>>>
>>>> Signed-off-by: Dan Murphy <dmurphy@ti.com>
>>>> ---
>>>>
>>>> v9 - Added back the CSR clearing as this is needed for TCAN device, fixed clean
>>>> function to clean index for version > 30, removed extra skb free and fixed work
>>>> handler to handle FIFO full for perpheral devices - https://lore.kernel.org/patchwork/patch/1050120/
>>>>
>>>> v8 - Added a clean function for the tx_skb, cleaned up skb on BUS_OFF and on xmit
>>>> BUSY - https://lore.kernel.org/patchwork/patch/1047980/
>>>> v7 - Fixed remaining new checkpatch issues, removed CSR setting, fixed tx hard
>>>> start function to return tx_busy, and renamed device callbacks - https://lore.kernel.org/patchwork/patch/1047220/
>>>> v6 - Squashed platform patch to this patch for bissectablity, fixed coding style
>>>> issues, updated Kconfig help, placed mcan reg offsets back into c file, renamed
>>>> priv->skb to priv->tx_skb and cleared perp interrupts at ISR start -
>>>> Patch 1 comments - https://lore.kernel.org/patchwork/patch/1042446/
>>>> Patch 2 comments - https://lore.kernel.org/patchwork/patch/1042442/
>>>>
>>>> drivers/net/can/m_can/Kconfig | 13 +-
>>>> drivers/net/can/m_can/Makefile | 1 +
>>>> drivers/net/can/m_can/m_can.c | 733 +++++++++++++------------
>>>> drivers/net/can/m_can/m_can.h | 110 ++++
>>>> drivers/net/can/m_can/m_can_platform.c | 202 +++++++
>>>> 5 files changed, 714 insertions(+), 345 deletions(-)
>>>> create mode 100644 drivers/net/can/m_can/m_can.h
>>>> create mode 100644 drivers/net/can/m_can/m_can_platform.c
>>>>
>>>> diff --git a/drivers/net/can/m_can/Kconfig b/drivers/net/can/m_can/Kconfig
>>>> index 04f20dd39007..f7119fd72df4 100644
>>>> --- a/drivers/net/can/m_can/Kconfig
>>>> +++ b/drivers/net/can/m_can/Kconfig
>>>> @@ -1,5 +1,14 @@
>>>> config CAN_M_CAN
>>>> + tristate "Bosch M_CAN support"
>>>> + ---help---
>>>> + Say Y here if you want support for Bosch M_CAN controller framework.
>>>> + This is common support for devices that embed the Bosch M_CAN IP.
>>>> +
>>>> +config CAN_M_CAN_PLATFORM
>>>> + tristate "Bosch M_CAN support for io-mapped devices"
>>>> depends on HAS_IOMEM
>>>> - tristate "Bosch M_CAN devices"
>>>> + depends on CAN_M_CAN
>>>> ---help---
>>>> - Say Y here if you want to support for Bosch M_CAN controller.
>>>> + Say Y here if you want support for IO Mapped Bosch M_CAN controller.
>>>> + This support is for devices that have the Bosch M_CAN controller
>>>> + IP embedded into the device and the IP is IO Mapped to the processor.
>>>> diff --git a/drivers/net/can/m_can/Makefile b/drivers/net/can/m_can/Makefile
>>>> index 8bbd7f24f5be..057bbcdb3c74 100644
>>>> --- a/drivers/net/can/m_can/Makefile
>>>> +++ b/drivers/net/can/m_can/Makefile
>>>> @@ -3,3 +3,4 @@
>>>> #
>>>>
>>>> obj-$(CONFIG_CAN_M_CAN) += m_can.o
>>>> +obj-$(CONFIG_CAN_M_CAN_PLATFORM) += m_can_platform.o
>>>> diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
>>>> index 9b449400376b..56336aefc567 100644
>>>> --- a/drivers/net/can/m_can/m_can.c
>>>> +++ b/drivers/net/can/m_can/m_can.c
> ... snip ...
>
>>>> +static netdev_tx_t m_can_start_xmit(struct sk_buff *skb,
>>>> + struct net_device *dev)
>>>> +{
>>>> + struct m_can_priv *priv = netdev_priv(dev);
>>>> +
>>>> + if (can_dropped_invalid_skb(dev, skb))
>>>> + return NETDEV_TX_OK;
>>>> +
>>>> + if (priv->is_peripherial) {
>>>> + if (priv->tx_skb) {
>>>> + netdev_err(dev, "hard_xmit called while tx busy\n");
>>>> + return NETDEV_TX_BUSY;
>>>> + }
>>>> +
>>>> + if (priv->can.state == CAN_STATE_BUS_OFF) {
>>>> + m_can_clean(dev);
>>>> + } else {
>>>> + priv->tx_skb = skb;
>>>> + queue_work(priv->tx_wq, &priv->tx_work);
>>>
>>> You removed "netif_stop_queue(cdev->net)" here. Does that work with just
>>> *one* "tx_skb"? I think you need an array then!? I'm afraid, this will
>>> require quite some changes and you should also measure the benefit of
>>> queuing outgoing messages first. For the time being, it would be fine
>>> for me to stop the queue here and add an appropriate comment.
>>>
>>
>> Yes I removed this in favor of allowing the work handler to stop the queue.
>>
>> If the version is < 30 then the queue is stopped immediately. If the version > 30 then the queue is
>> only stopped if FIFO is full.
>
> Yes, and the next call to m_can_start_xmit() will probably return with
> NETDEV_TX_BUSY. You should at least add a "netif_stop_queue(cdev->net)"
> before returning NETDEV_TX_BUSY, otherwice the upper layer will retry
> immediately resulting in high CPU load. Anyway, the purpose of this
> return code is to signal errors/bugs in the start/stop flow control:
>

Ack

> https://elixir.bootlin.com/linux/latest/source/Documentation/networking/netdevices.txt#L81
>
>>
>> I did see the message "tcan4x5x spi1.0 can0: hard_xmit called while tx busy"
>> more with no gap and no polling in the cangen request.
>
> You usually should never see that message.
>
>>
>>> BTW, how big is the FIFO size on your system:
>>>
>>
>> This value is set to 1.
>>
>>> tx_fifo_size = mram_config_vals[7];
>
> Then I'm surprised that you see "hard_xmit called while tx busy" at all.
> Are you sure that "cdev->version" is 32 on the tcan4x5?
>

tcan4x5x spi1.0 can0: Version of M_CAN is 32

> Wolfgang
>


--
------------------
Dan Murphy

\
 
 \ /
  Last update: 2019-03-15 15:53    [W:0.041 / U:13.116 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site