lkml.org 
[lkml]   [2019]   [Mar]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [linux-sunxi] [PATCH 3/6] drm/sun4i: dsi: Add bridge support
From
Date
Hi,

On Fri, 2019-03-15 at 14:45 +0100, Maxime Ripard wrote:
> On Fri, Mar 15, 2019 at 02:32:55PM +0100, Paul Kocialkowski wrote:
> > Hi,
> >
> > On Fri, 2019-03-15 at 18:38 +0530, Jagan Teki wrote:
> > > Some display panels would come up with a non-DSI output which
> > > can have an option to connect DSI interface by means of bridge
> > > convertor.
> > >
> > > This DSI to non-DSI bridge convertor would require a bridge
> > > driver that would communicate the DSI controller for bridge
> > > functionalities.
> > >
> > > So, add support for bridge functionalities in Allwinner DSI
> > > controller.
> >
> > See a few comments below.
> >
> > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > > ---
> > > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 65 +++++++++++++++++++-------
> > > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h | 1 +
> > > 2 files changed, 49 insertions(+), 17 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > > index 0960b96b62cc..64d74313b842 100644
> > > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > > @@ -781,6 +781,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder)
> > > if (!IS_ERR(dsi->panel))
> > > drm_panel_prepare(dsi->panel);
> > >
> > > + if (!IS_ERR(dsi->bridge))
> > > + drm_bridge_pre_enable(dsi->bridge);
> > > +
> > > /*
> > > * FIXME: This should be moved after the switch to HS mode.
> > > *
> > > @@ -796,6 +799,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder)
> > > if (!IS_ERR(dsi->panel))
> > > drm_panel_enable(dsi->panel);
> > >
> > > + if (!IS_ERR(dsi->bridge))
> > > + drm_bridge_enable(dsi->bridge);
> > > +
> > > sun6i_dsi_start(dsi, DSI_START_HSC);
> > >
> > > udelay(1000);
> > > @@ -812,6 +818,9 @@ static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder)
> > > if (!IS_ERR(dsi->panel)) {
> > > drm_panel_disable(dsi->panel);
> > > drm_panel_unprepare(dsi->panel);
> > > + } else if (!IS_ERR(dsi->bridge)) {
> > > + drm_bridge_disable(dsi->bridge);
> > > + drm_bridge_post_disable(dsi->bridge);
> > > }
> > >
> > > phy_power_off(dsi->dphy);
> > > @@ -973,11 +982,16 @@ static int sun6i_dsi_attach(struct mipi_dsi_host *host,
> > > struct sun6i_dsi *dsi = host_to_sun6i_dsi(host);
> > >
> > > dsi->device = device;
> > > - dsi->panel = of_drm_find_panel(device->dev.of_node);
> > > - if (IS_ERR(dsi->panel))
> > > - return PTR_ERR(dsi->panel);
> > >
> > > - dev_info(host->dev, "Attached device %s\n", device->name);
> > > + dsi->bridge = of_drm_find_bridge(device->dev.of_node);
> > > + if (!dsi->bridge) {
> >
> > You are using IS_ERR to check that the bridge is alive in the changes
> > above, but switch to checking that it's non-NULL at this point.
> >
> > Are both guaranteed to be interchangeable?
>
> They aren't. Any ERR_PTR will be !NULL
>
> > > + dsi->panel = of_drm_find_panel(device->dev.of_node);
> > > + if (IS_ERR(dsi->panel))
> > > + return PTR_ERR(dsi->panel);
> > > + }
> >
> > You should probably use drm_of_find_panel_or_bridge instead of
> > duplicating the logic here.
>
> Or we can even use the drm_panel_bridge_add to simplify things.

Indeed, I was just looking at that and it seems to be specifically
tailored for this use case.

Cheers,

Paul

--
Paul Kocialkowski, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com

\
 
 \ /
  Last update: 2019-03-15 14:49    [W:0.037 / U:2.836 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site