lkml.org 
[lkml]   [2019]   [Feb]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH V13 3/5] i2c: tegra: Add DMA support
From
Date
06.02.2019 17:47, Sowjanya Komatineni пишет:
> This patch adds DMA support for Tegra I2C.
>
> Tegra I2C TX and RX FIFO depth is 8 words. PIO mode is used for
> transfer size of the max FIFO depth and DMA mode is used for
> transfer size higher than max FIFO depth to save CPU overhead.
>
> PIO mode needs full intervention of CPU to fill or empty FIFO's
> and also need to service multiple data requests interrupt for the
> same transaction. This adds delay between data bytes of the same
> transfer when CPU is fully loaded and some slave devices has
> internal timeout for no bus activity and stops transaction to
> avoid bus hang. DMA mode is helpful in such cases.
>
> DMA mode is also helpful for Large transfers during downloading or
> uploading FW over I2C to some external devices.
>
> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
> ---

[snip]

> +static void tegra_i2c_config_fifo_trig(struct tegra_i2c_dev *i2c_dev,
> + size_t len)
> +{
> + u32 val, reg;
> + u8 dma_burst = 0;
> + struct dma_slave_config slv_config = {0};
> + struct dma_chan *chan;
> + int ret;
> +
> + if (i2c_dev->hw->has_mst_fifo)
> + reg = I2C_MST_FIFO_CONTROL;
> + else
> + reg = I2C_FIFO_CONTROL;
> + val = i2c_readl(i2c_dev, reg);
> +
> + if (i2c_dev->is_curr_dma_xfer) {
> + if (len & 0xF)
> + dma_burst = 1;
> + else if (len & 0x10)
> + dma_burst = 4;
> + else
> + dma_burst = 8;
> +
> + if (i2c_dev->msg_read) {
> + chan = i2c_dev->rx_dma_chan;
> + slv_config.src_addr = i2c_dev->base_phys +
> + tegra_i2c_reg_addr(i2c_dev, I2C_RX_FIFO);
> + slv_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
> + slv_config.src_maxburst = dma_burst;
> +
> + if (i2c_dev->hw->has_mst_fifo)
> + val |= I2C_MST_FIFO_CONTROL_RX_TRIG(dma_burst);
> + else
> + val |= I2C_FIFO_CONTROL_RX_TRIG(dma_burst);
> + } else {
> + chan = i2c_dev->tx_dma_chan;
> + slv_config.dst_addr = i2c_dev->base_phys +
> + tegra_i2c_reg_addr(i2c_dev, I2C_TX_FIFO);;

Two ";;" at the end.

[snip]

Good news: DVC I2C works now and tps6586x probes fine! :)
Bad news: atmel-touch still has same problems as in V12 :(

DMA-only V13: http://dpaste.com/0XJ1Z8G.txt

\
 
 \ /
  Last update: 2019-02-06 16:03    [W:0.122 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site