lkml.org 
[lkml]   [2019]   [Feb]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 10/10] venus: dec: make decoder compliant with stateful codec API
On Fri, Feb 1, 2019 at 12:18 AM Nicolas Dufresne <nicolas@ndufresne.ca> wrote:
>
> Le jeudi 31 janvier 2019 à 22:34 +0900, Tomasz Figa a écrit :
> > On Thu, Jan 31, 2019 at 9:42 PM Philipp Zabel <p.zabel@pengutronix.de> wrote:
> > > Hi Nicolas,
> > >
> > > On Wed, 2019-01-30 at 10:32 -0500, Nicolas Dufresne wrote:
> > > > Le mercredi 30 janvier 2019 à 15:17 +0900, Tomasz Figa a écrit :
> > > > > > I don't remember saying that, maybe I meant to say there might be a
> > > > > > workaround ?
> > > > > >
> > > > > > For the fact, here we queue the headers (or first frame):
> > > > > >
> > > > > > https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/blob/master/sys/v4l2/gstv4l2videodec.c#L624
> > > > > >
> > > > > > Then few line below this helper does G_FMT internally:
> > > > > >
> > > > > > https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/blob/master/sys/v4l2/gstv4l2videodec.c#L634
> > > > > > https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/blob/master/sys/v4l2/gstv4l2object.c#L3907
> > > > > >
> > > > > > And just plainly fails if G_FMT returns an error of any type. This was
> > > > > > how Kamil designed it initially for MFC driver. There was no other
> > > > > > alternative back then (no EAGAIN yet either).
> > > > >
> > > > > Hmm, was that ffmpeg then?
> > > > >
> > > > > So would it just set the OUTPUT width and height to 0? Does it mean
> > > > > that gstreamer doesn't work with coda and mtk-vcodec, which don't have
> > > > > such wait in their g_fmt implementations?
> > > >
> > > > I don't know for MTK, I don't have the hardware and didn't integrate
> > > > their vendor pixel format. For the CODA, I know it works, if there is
> > > > no wait in the G_FMT, then I suppose we are being really lucky with the
> > > > timing (it would be that the drivers process the SPS/PPS synchronously,
> > > > and a simple lock in the G_FMT call is enough to wait). Adding Philipp
> > > > in CC, he could explain how this works, I know they use GStreamer in
> > > > production, and he would have fixed GStreamer already if that was
> > > > causing important issue.
> > >
> > > CODA predates the width/height=0 rule on the coded/OUTPUT queue.
> > > It currently behaves more like a traditional mem2mem device.
> >
> > The rule in the latest spec is that if width/height is 0 then CAPTURE
> > format is determined only after the stream is parsed. Otherwise it's
> > instantly deduced from the OUTPUT resolution.
> >
> > > When width/height is set via S_FMT(OUT) or output crop selection, the
> > > driver will believe it and set the same (rounded up to macroblock
> > > alignment) on the capture queue without ever having seen the SPS.
> >
> > That's why I asked whether gstreamer sets width and height of OUTPUT
> > to non-zero values. If so, there is no regression, as the specs mimic
> > the coda behavior.
>
> I see, with Philipp's answer it explains why it works. Note that
> GStreamer sets the display size on the OUTPUT format (in fact we pass
> as much information as we have, because a) it's generic code and b) it
> will be needed someday when we enable pre-allocation (REQBUFS before
> SPS/PPS is passed, to avoid the setup delay introduce by allocation,
> mostly seen with CMA base decoder). In any case, the driver reported
> display size should always be ignored in GStreamer, the only
> information we look at is the G_SELECTION for the case the x/y or the
> cropping rectangle is non-zero.
>
> Note this can only work if the capture queue is not affected by the
> coded size, or if the round-up made by the driver is bigger or equal to
> that coded size. I believe CODA falls into the first category, since
> the decoding happens in a separate set of buffers and are then de-tiled
> into the capture buffers (if understood correctly).

Sounds like it would work only if coded size is equal to the visible
size (that GStreamer sets) rounded up to full macroblocks. Non-zero x
or y in the crop could be problematic too.

Hans, what's your view on this? Should we require G_FMT(CAPTURE) to
wait until a format becomes available or the OUTPUT queue runs out of
buffers?

>
> I would say, best is just to test the updated Venus driver, which is in
> my queue.

The updated Venus driver doesn't implement the behavior I referred to,
but rather the legacy wait in G_FMT(CAPTURE) as in s5p-mfc.

\
 
 \ /
  Last update: 2019-02-05 07:27    [W:0.122 / U:4.704 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site