lkml.org 
[lkml]   [2019]   [Feb]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 9/9] ARM: dts: stm32: add joystick support on stm32mp157c-ev1
Date
The joystick (B1) on stm32mp157c-ev1 uses gpios on STMFX gpio expander.
These gpios need a pin configuration (push-pull and bias-pull-down),
described under stmfx_pinctrl node.

Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 44 +++++++++++++++++++++++++++++++++++
1 file changed, 44 insertions(+)

diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 3a6f033..6d6b692 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -7,6 +7,7 @@

#include "stm32mp157c-ed1.dts"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>

/ {
model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
@@ -21,6 +22,43 @@
ethernet0 = &ethernet0;
};

+ joystick {
+ compatible = "gpio-keys";
+ #size-cells = <0>;
+ pinctrl-0 = <&joystick_pins>;
+ pinctrl-names = "default";
+ button-0 {
+ label = "JoySel";
+ linux,code = <KEY_ENTER>;
+ interrupt-parent = <&stmfx_pinctrl>;
+ interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+ };
+ button-1 {
+ label = "JoyDown";
+ linux,code = <KEY_DOWN>;
+ interrupt-parent = <&stmfx_pinctrl>;
+ interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+ };
+ button-2 {
+ label = "JoyLeft";
+ linux,code = <KEY_LEFT>;
+ interrupt-parent = <&stmfx_pinctrl>;
+ interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+ };
+ button-3 {
+ label = "JoyRight";
+ linux,code = <KEY_RIGHT>;
+ interrupt-parent = <&stmfx_pinctrl>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ };
+ button-4 {
+ label = "JoyUp";
+ linux,code = <KEY_UP>;
+ interrupt-parent = <&stmfx_pinctrl>;
+ interrupts = <4 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
+
panel_backlight: panel-backlight {
compatible = "gpio-backlight";
gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
@@ -113,6 +151,12 @@
interrupt-controller;
#interrupt-cells = <2>;
gpio-ranges = <&stmfx_pinctrl 0 0 24>;
+
+ joystick_pins: joystick {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
+ drive-push-pull;
+ bias-pull-down;
+ };
};
};
};
--
2.7.4
\
 
 \ /
  Last update: 2019-02-27 10:35    [W:0.130 / U:69.512 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site